Table of Contents
Advertisement
2 - In the text box, type in the height to which you want the platform to move to,
In the text box, type in the height to which you want the platform to move to,
In the text box, type in the height to which you want the platform to move to,
and click the "To" button. In the above examp
and click the "To" button. In the above example, the platform would m
119.2mm above the platform's origin.
mm above the platform's origin.
3 - Check the distance between the nozzle and the platform. If, for example,
Check the distance between the nozzle and the platform. If, for example,
Check the distance between the nozzle and the platform. If, for example,
the platform appears to be about 7mm away from the nozzle, increase the
the platform appears to be about 7mm away from the nozzle, increase the
the platform appears to be about 7mm away from the nozzle, increase the
number in the text box to 120 and click the "To" button. Note that we have
number in the text box to 1
only increased the number by 3mm instead of 4mm. The reason for this is
only increased the number by 3mm instead of 4mm. The reason for this is
only increased the number by 3mm instead of 4mm. The reason for this is
that we do not want to crash the platform into the nozzle, so we want to
that we do not want to crash the platform into the nozzle, so we want to
that we do not want to crash the platform into the nozzle, so we want to
increase the height in smaller and smaller increments as we get closer to
increase the height in smaller and smaller increments as we get closer to
increase the height in smaller and smaller increments as we get closer to
the nozzle.
4 - Once you are about 1mm away from the nozzle, start increasing the
Once you are about 1mm away from the nozzle, start increasing the
Once you are about 1mm away from the nozzle, start increasing the
number in the text box by 0.1mm increments and click the "To" button.
number in the text box by 0.1mm increments and click the "To" button.
number in the text box by 0.1mm increments and click the "To" button.
Repeat this until you get to within 0.2mm of the nozzle.
Repeat this until you get to within 0.2mm of the nozzle.
TIP: An easy way to check the distance betwe
An easy way to check the distance between the nozzle and platform is to
fold a piece of paper in two (Which will make it about 0.2mm thick) and
fold a piece of paper in two (Which will make it about 0.2mm thick) and
fold a piece of paper in two (Which will make it about 0.2mm thick) and
use that as a spacer to gauge the distance between the nozzle and
use that as a spacer to gauge the distance between the nozzle and
use that as a spacer to gauge the distance between the nozzle and
platform.
5 - Once you are within 0.2mm of the nozzle, write down the number you h
Once you are within 0.2mm of the nozzle, write down the number you h
Once you are within 0.2mm of the nozzle, write down the number you have
in the "To" box. This is the correct calibration height! Close the "Maintain"
in the "To" box. This is the correct calibration height! Close the "Maintain"
in the "To" box. This is the correct calibration height! Close the "Maintain"
window and open the "Setup" Window. In the "Setup" window "Nozzle" box,
window and open the "Setup" Window. In the "Setup" window "Nozzle" box,
window and open the "Setup" Window. In the "Setup" window "Nozzle" box,
enter the number you recorded on the "Maintain" Screen. Alternatively, you
enter the number you recorded on the "Maintain" Screen. Alternatively, you
enter the number you recorded on the "Maintain" Screen. Alternatively, you
can click the "Set to Nozzl
can click the "Set to Nozzle Height" button to automatically transfer the
value across to the setup screen. You have now successfully setup the
value across to the setup screen. You have now successfully setup the
value across to the setup screen. You have now successfully setup the
nozzle height.
6 – Now click "Goto Bottom" in the Maintenance screen.
Now click "Goto Bottom" in the Maintenance screen.
NOTE: Once you have setup the nozzle height once, you do not need to
NOTE: Once you have setup the nozzle height once, you do not need to
NOTE: Once you have setup the nozzle height once, you do not need to
do it again as it is automatically recorded in the "Setup" Screen.
do it again as it is automatically recorded in the "Setup" Screen.
do it again as it is automatically recorded in the "Setup" Screen.
UP Mini 3D Printer User Manual
3D Printer User Manual
, the platform would move to
the "To" button. Note that we have
en the nozzle and platform is to
e Height" button to automatically transfer the
3. Operation
Operation
16
Advertisement
Table of Contents
Need help?
Do you have a question about the UP Mini and is the answer not in the manual?