Page 2
IR Vandal Dome Camera MANUAL 사용 설명서 용 서 DIC-7030DV 680TVL...
Page 3
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert...
Page 4
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
It could cause an electric shock. Do not disassemble the camera. It may result in fire, electric shock or other hazards. Do not use the camera close to a gas or oil leak. It may result in fire or other hazards. ■...
1. Features ■SONY 1/3" 480K/570K-Effective Pixel Ex-view HAD CCD II Minimum Resolution 0.1 Lux (F1.2, 50 IRE) ■High Resolution: More than 680 TV Lines This camera has realized high resolution of 680 TV lines using the top-notch full digital image processing, 12 Bit A/D serial signal processing and special algorithm technologies. ■NR (Digital Noise Reduction) The DNR technology eliminates noise thus generating a distinct and clear image.
2. Cable Connection & OSD Control 1) Cable Connection ( DC12V Type ) (Dual Type DC12/AC24V) 2) OSD Control ① 3AXIS BRACKET - Please loosen screws and fix tilted and panned position. ③ LENS : Vari-Focal Auto Iris Lens ( 2.8mm ~ 12.0mm / F1.2 ) with ICR OSD PCB - SETUP button : Used for the menu display.
3. Setup Menu Operation •Please press the SETUP button to set OSD menu. The SETUP menu is displayed like under the picture on the monitor. • if it has been selected. You may move up/down to use another function by up/down buttons and change the status by pressing left/right buttons.
Page 10
•AUTO (HIGH LUMINANCE) - AUTO IRIS Select this to control the shutter speed automatically. -SHUT+AUTO IRIS Select AE control on the medium and high brightness side -Brightness Select the high and medium brightness side reference (LOW LUMINANCE) -AGC Select AE control on the low-brightness side -Brightness Select the low brightness side reference •MANUAL...
Page 11
•ATW - SPEED Adjusts the pull-in speed ATW - DELAY CNT Sets the time-based hysteresis of ATW - ATW FRAME Sets the pull-in frame magnification - ENVIROMENT Sets the pull-in frame(indoor/outdoor)of ATW •USER1 - B-GAIN Used for operating the B gain in the WB fixed gain mode -R-GAIN Used for operating the R gain in the WB fixed gain...
Page 12
BACKLIGHT SETUP MENU •OFF LENS AUTO Backlight compensation OFF SHUTTER/AGC AUTO •BLC WHITE BAL BACKLIGHT Backlight compensation ON PICT ADJUST •HLC MOTION DET High light compensation ON NEXT EXIT SAVE ALL PICT ADJUST SETUP MENU LENS AUTO SHUTTER/AGC AUTO WHITE BAL BACKLIGHT PICT ADJUST MOTION DET...
Page 13
•LUMINANCE Sets the extent of the luminance compression (LOW/MID/HIGH) •CONTRAST Sets the extent of the contrast enhancement (LOW/MIDDLE/MID/MIDHIGH/HIGH) MOTION DET SETUP MENU LENS AUTO SHUTTER/AGC AUTO WHITE BAL BACKLIGHT PICT ADJUST MOTION DET NEXT EXIT SAVE ALL •DETECT SENSE: Sets the motion detection sensitivity •BLOCK DISP OFF: Controls the ON/OFF status of the motion detection block display •BLACK DISP ENABLE: The display switches to the "dead band setting"...
Page 14
PRIVACY SETUP MENU PRIVACY DAY/NIGHT AUTO CAMERA ID SYNC LANGUAGE ENGLISH CAMERA RESET BACK EXIT SAVE ALL •AREA SEL: Selects the mask frame to be adjusted •TOP: Sets the top side of the mask frame selected by the AREA SEL parameter •BOTTOM: Sets the bottom side of the mask frame selected by the AREA SEL parameter.
Page 15
Set the threshold for identifying the Day status from the Night status. •B/W -BURST Burst signal OFF enable, Burst signal ON •COLOR The picture is always displayed in color. The function is used to set the noise reduction SETUP MENU PRIVACY -NR MODE DAY/NIGHT...
Page 16
•↑↓→ ← The camera ID cursor moves •CLR The character selected by the camera ID cursor is cleared •POS The display switches to the camera ID display position setting screen SYNC •INT SETUP MENU Internal mode PRIVACY DAY/NIGHT AUTO •LL Line lock mode CAMERA ID SYNC...
4. Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. • Nothing appears on the screen. Check that the power cord and line connection between the camera and monitor are fixed properly.
6. Specifications ▪ GENERAL Signal system NTSC Sony 1/3" 480K/570K-Effective Ex-view HAD CCD Ⅱ Image Sensor 1020(H) × 596(V) 1020(H) × 596(V) Total Pixels 976(H) × 494(V) 976(H) × 582(V) Effective Pixels 680 TV lines Resolution Syns. Inter. H/V 15.734/ 59.94Hz 15.625K/50Hz IR On : 0 Lux MIN.
Need help?
Do you have a question about the DIC-7030DV and is the answer not in the manual?
Questions and answers