Bosch 2600 Series Instruction Manual page 44

LTC 2600 Series | Instruction Manual | Appendix A
CCL Grammar Parameter Definitions
<monitor> = 1 | 2 1 = Monitor A
2 = Monitor B
<mon-mode> = 1 | 2 1 = Full mode
2 = Quad mode
<operation> = 1..6 1 = live
2 = record
3 = playback
4 = playback-record (duplex and duplex-extended only)
5 = record-record (duplex-extended only)
6 = playback-playback (duplex-extended only)
<pan speed> = 0..15
<password> = <digit> <digit> <digit> <digit>
<play-times> = 0 | 1
0 = SP
1 = LP
<polarity> = 0 | 1
0 = Normally open
1 = Normally closed
<pre-position#> = 1..99
<ptz code> = any combination of
0x000
0x001
0x002
0x004
0x008
0x010
0x020
0x040
0x080
0x100
0x200
<r/c opcode> = 1 | 2 | 3 | 4 | 5 | 6 | 7 | 10 | 11 | 12
<r/c data> 0..15
<record mode> = 0 | 1 | 2
0 = Off
1 = Exclusive
2 = Interleave
<record speed> = 1..20
<responds to> = 0 | 1 | 2 | 3
0 = Neither
1 = Action
2 = Alarm
3 = Both
Bosch Security Systems | July 12, 2004
All off
Pan right
Pan left
Tilt down
Tilt up
Zoom out
Zoom in
Focus near
Focus far
Iris close
Iris open
CCL Grammar Parameter Definitions
<revision> = <major revision> SPACE <minor revision> [SPACE E <engineering
revision>]
<major revision> = <0..99>
<major revision> = <0..99>
<engineering revision> = <0..99>
<seq device> = 0 | 1 | 2
0 = MonA Full
1 = MonA Quad
2 = MonB Full
<seq mode> = 1..5
1..4= QuadA..QuadD
5 = Full
<setup#> = 1 | 2 | 3 | 4 | 5 | 6
<standard-vcr- from 7 on
model#> = Provisionally (see User Interface for latest list)
7 = PHILIPS_KV_7024
8 = PHILIPS_TC3990A_SP_T120,
9 = PHILIPS_TC3990A_SLP_T120,
10 = PHILIPS_TC3991,
11 = MITSUBISHI_HS5440U,
12 = SANYO_SRT500,
13 = JVC_SR_L901U,
14 = PANASONIC_AG_RT600,
15 = SP_T120_FIELD,
16 = SP_T160_FIELD,
17 = SLP_T120_FIELD,
18 = SLP_T160_FIELD,
19 = SP_T120_FRAME,
20 = SP_T160_FRAME,
21 = SLP_T120_FRAME,
22 = SLP_T160_FRAME
<tilt speed> = 0..15
<timelapse mode> = 1 | 2
1 = Normal
2 = Action/Alarm
<unit address> = 1..30
<vcr> = 1 | 2
1 = Vcr output
2 = Vcr/MonB output
<vcr-mode> = 1..20
<vcr-model#> = <standard-vcr-model#> | <custom-vcr-model#>
<zone draw setting> = 0 | <camera#>
0 = disabled
<zone map> = <16-bit map> x 16
An active zone map consists of a list of 16 unsigned short
integers. Each 16 bit integer corresponds to the zone map for a
single row on screen. Each bit on the integer corresponds to a
single zone point. The most significant bit (b15) corresponds to
the leftmost zone point in the row. The first integer in the list
corresponds to the topmost row on the screen. A set bit
corresponds to an active zone point.
<zoom speed> = 0..7
EN | 44