Maintenance–Washing Instructions; Disassembling The Fabric Components For Washing; Assembling The Fabric Components After Washing; Assembling The Hood - Stokke XPLORY User Manual

Disassembling the fabric
components for washing:
Disassembling the hood (20)
Unzip to release the hood. Unbutton
on each side of the hood. Pull up the
fabric on the side and the front to
reveal the hood fastener. Press the
notch on the hood fastener and pull
up the hood. Repeat at the other side.
Remove the main rib before washing.
Disassembling the back cover (21)
Loosen the fabric from the push
buttons on each side and from the two
in front. Pull the fabric off the Velcro.
Disassembling the fabric on the seat
guard (22)
Release the rib by pressing a thin pin
or screwdriver into the little hole on
each side. Open textile tab and unzip.
Loosen the fabric from the hook on
both side of the rib.
Disassembling Seat rail cover
Remove by pulling off.
Disassembling Harness covering
Remove by pulling off.
Disassembling Seat cover (23)
Loosen the orange tag on each side of
the bottom rear of the back. Remove
the safety harness. Gently pull the
seat fabric up until it is completely off.
MAINTENANCE – WASHING
INSTRUCTIONS
Hard parts
The stroller should be cleaned using
a mild mixture of soap and water.
Make sure that any sand/mud/grit is
removed prior to cleaning. No part of
the stroller is to be lubricated. If any
function of the stroller is not working
properly, contact your
nearest STOKKE retailer.
Textiles must be washed separately
(24)
When washing the baby insert,
please remove the inside cushion
before washing the cover.
Remove the ribs before washing
the canopy. Release the main rib by
pressing, e.g., a screwdriver into
the small holes in the canopy
fasteners. Afterwards, thread all
the ribs out of the fabric.
STOKKE XPLORY
®
Assembling the fabric components after
washing:
Assembling the Seat cover (25)
Insert the rails on the seat cover into
the slot on each side. Pull the seat cover
down. Position the harness. Crotch, waist
and shoulder straps. Make sure that
shoulder straps
correspond to the child's shoulder height.
Fasten the orange tag on each side of the
bottom rear of the back. Conceal the end
of the orange tag in the seat. Pull the fab-
ric over the back.
Assembling the fabric on the seat guard
(26)
Release the rib by pressing a thin pin or
screwdriver into the little hole on each
side. Fasten the beginning of the zipper
around the bar with Velcro facing out.
Make sure that the tap goes through the
fabric. Pull up the zip with tap through
center and end. Fasten the rib by pressing
it into place.
Note! The rib can be mounted wrong!
Assembling the back cover (27)
Line up the center mark on the fabric to
the corresponding center mark on the
seat guard. Attach the cover edge-to-
edge on the Velcro. Attach the cover with
the push buttons, 2 on each side, and with
the two on each side of the front.

Assembling the hood (28)

Insert the main rib after washing. Make
sure the notch on the main rib is facing
front. Insert the main rib into both sides
of the hood fastener. A click will be heard
when the rib is placed correctly. Fasten
the hood with the push buttons on each
side. Zip the hood onto the seat fabric.
Assembling the harness covering
Enter the harness covering with the soft
side facing the child.
Assembling the seat rail cover
Enter the cover by pulling it on.
Basic mosquito net (29)
Pull the mosquito net over the handle and
the footrest. Pull the mosquito net over
the main rib of the hood. Snap on the
mosquito net using the push
buttons on each side. Pull the net until
the seat is completely covered. Pull up
the zippers on each side of the central
bar.
Basic rain cover(30)
Pull the rain cover over the handle and
the footrest. Pull the rain cover over the
hood. Fasten using the Velcro around the
central bar and footrest. Pull up the
zippers on each side of the central bar.
®
Basic shopping bag(31)
Place the shopping bag on the board.
Fasten around the central bar using
the attached hook.
Changing bag
Attach the changing bag to the seat
arm.
Stokke® Warranty card / Product
registration card:
See description of where to find the
products serial number/date clock on
your product. Use this information
when filling out the Stokke warranty
card / Product registration card. We
recommend that you fill in this
information at www.stokke.com.
17