Programmable Features - Clifford Prime Level TWO Installation Manual

The Level TWO comes preprogrammed as noted in bold text in the following tables.
Programming User-Selectable Features
1. Note the column (across) and row (down) numbers of the feature(s) you wish to program.
2. Turn the ignition to the "ON" position or start the engine.
3. Enter the factory preset valet/programming code of "2" by toggling the valet switch
(located behind the LED assembly) to the left two times, then to the right (LED on).
4. Immediately hold to the left for about 3 seconds until you hear one horn beep and the
LED turns on to confirm the system is in the "Feature Select" position.
5. Select the feature column: Toggle the switch to the right the number of times indicated
for the column. Pause. You will hear the same number of horn beeps, confirming your
selection.
6. Within five seconds, select the feature row: Toggle the switch to the left the number of
times indicated for the row. You'll hear a beep each time to help you count.
7. If there is a NOTE for the selected feature, perform the actions noted.
8. Pause. You will hear either one or two beeps: two beeps = ON, one beep = OFF.
9. You can select another feature, or you can exit program mode:
a. To select another feature in that same column, repeat step 6 within the next five
seconds (after five seconds, three beeps indicate return to the "Feature Select" position).
b. To select a different feature column, repeat step 5.
c. To exit program mode, turn the ignition off (you'll hear three beeps and the LED will
turn off), or wait 60 seconds for the system to automatically exit program mode.
Table of User-Selectable Features: 1 beep = OFF, 2 beeps= ON
Feature
Select Right x 1
Add a new remote
Left x
1
NOTE 1
Personalized Siren
Left x
Sounds*
2
NOTE 2
Play Siren Sounds*:
Left x
trigger only/always
3
(1/2 beeps)
Siren duration:
Left x
30/60/90sec.
4
(1/2/3 beeps)
Left x AutoLock: off/on/rpm*
5
(1/2/3 beeps)
Left x
AutoUnLock: off/on
6
Reset all features to
Left x
default (except
7
remotes & valet code)
** In Dealer Mode (see page 3), beeps/chirps are off; AutoArming and Lock upon AutoArm are on
Press the lock button of the new vehicle buyer’s remote. You’ll hear one beep. Press the
n
NOTE 1:
lock button You’ll hear two beeps to confirm that the new remote control has been added.
again.

Programmable Features

Right x 2 Right x 3
Chirps*/beeps:
off**/on/quiet AutoArming:
(1/2/3* off/on**
chirps*/beeps)
Lock upon
NOT USED
AutoArming:
off/on**
AutoArming
NOT USED
entry delay:
off/on
AutoStart*: both
off/both on/temp
FACT: off/on
only/battery only
(1/2/3/4 beeps)
NOT USED NOT USED
Clear all remotes
NOT USED
NOTE 3
Set a new secret
NOT USED
valet code
NOTE 4
8
Right x 4
NOTE 5 — Other remote:
arm (1 then 2 beeps)
NOTE 6 — Other remote:
trunk release (2 beeps)
NOTE 6 — Other remote:
panic (3 beeps)
NOTE 6 — Other remote:
disarm (4 beeps)
NOTE 6 — Other remote:
remote starting* (5 beeps)
NOTE 6 — Other remote:
window rolldown/venting*
(6 beeps)
NOTE 6 — Other remote:
valet mode (7 beeps)
* Requires optional G4 accessory