Related Manuals for Clifford Prime Level Three Security Upgrade Package
Summary of Contents for Clifford Prime Level Three Security Upgrade Package
- Page 1 Color profile: Disabled Composite Default screen The Science of Security™ Prime Level THREE SECURITY UPGRADE PACKAGE Installation Manual D:...-923 Level 3 install manual.vp Mon Aug 02 10:56:45 1999...
-
Page 2: Table Of Contents
Color profile: Disabled Composite Default screen Table of Contents Wiring Diagram ........2 Important Information . -
Page 3: Wiring Diagram
Color profile: Disabled Composite Default screen Siren/Car Horn passenger kick panel Parking Lights driver kick panel Output Factory Keyless Entry Factory Module Car Horn Relay UNLOCK Car Horn LOCK +12V UNLOCK +12V UNLOCK +12V LOCK +12V LOCK Optional Parking White/Green to rear doors Light Relay (arm input +) -
Page 4: Important Information
2. Keep extension, if needed, as short as possible. Use same-gauge wire for extensions. 3. DO NOT mount components nor route wires near hot or moving vehicle parts. NOTE: Clifford Electronics’ web site for Authorized Clifford Dealers has detailed descriptions of wire colors and locations for most foreign and domestic vehicles. -
Page 5: Door Trigger
Color profile: Disabled Composite Default screen Door Trigger Door triggers on most vehicles are negative. To verify polarity: 1. Find the one wire off the rear of the door switch that shows +12 volts when the switch is pressed in and 0 volts when released. This is a negative trigger door wire. 2. -
Page 6: Optional Dual-Zone Piezo Vibration/Impact Sensor
Color profile: Disabled Composite Default screen Optional Dual-Zone Piezo Vibration/Impact Sensor Mount the sensor in the passenger compartment, not in the engine compartment. 1. Firmly mount the sensor near the base of the steering column (if the steering column has a rotating sleeve, firmly screw the sensor to the interior firewall, kick panel or trunk wall). -
Page 7: Eight-Event Totalrecall
Color profile: Disabled Composite Default screen Eight-Event TotalRecall 1. With the ignition OFF, press and hold the valet switch (at the rear of the LED assembly) to the right. 2. Use the remote control to lock, then unlock, then release the valet switch. 3. -
Page 8: Installer Programmable Features
Color profile: Disabled Composite Default screen User-Selectable Features (Customer Mode): 1 beep = OFF, 2 beeps= ON Right x 1 Feature Select NOTE 1: Immediately toggle , then enter the new code, right Left x 1 Beeps: off/on/soft (1/2/3 beeps) , then wait for the two beeps turn off the ignition (3 beeps). -
Page 9: System Checklist & Troubleshooting
NOTE: If you are still having trouble after performing the following steps, please call Clifford Technical Support Services at 1-800-444-4667. Step 1: Test the immobilization circuit. Arm the system by pressing the LOCK button on the factory remote from inside the vehicle and wait 10 seconds. - Page 10 If either of these test fail, adjust the sensor using the adjustment knob and retest. Keep in mind that the sensor does not come online until about 70 seconds after arming. Step 10: Adhere the Clifford window decals to the vehicle’s front windows. D:...-923 Level 3 install manual.vp...
- Page 11 Color profile: Disabled Composite Default screen D:...-923 Level 3 install manual.vp Mon Aug 02 10:56:57 1999...
- Page 12 Netherlands Headquarters Trompenburgstraat 8A 1079 TX Amsterdam 020 40 40 919 Clifford systems are covered by one or more of these Clifford Electronics USA patents: 4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464; 4,887,064; 4,890,108; 4,922,224; 4,997,053; 5,081,667; 5,146,215; 5,157,375; 5,467,070; 5,650,744 and other patents pending AutoFax &...
Need help?
Do you have a question about the Prime Level Three Security Upgrade Package and is the answer not in the manual?
Questions and answers