1. Manuals
  2. Brands
  3. Premium Leisure Manuals
  4. Hot Tub
  5. Swimmer's Edge 18
  6. Owner's manual

Premium Leisure Swimmer’s Edge 18 Owner's Manual

Premium leisure swim spas owner’s manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

SWIM SPAS OWNER'S MANUAL
MODELS: SWIMMER'S EDGE 18, DUAL ZONE 18,
SWIMMER 18, SWIMMER 14
Premium Leisure, LLC
th
6101 45
St. N.
St. Petersburg, FL 33714
727.573.9611
www.PremiumLeisure.com
Part Number 7068
Revised 03/10

Advertisement

Table of Contents
loading

Related Manuals for Premium Leisure Swimmer’s Edge 18

Summary of Contents for Premium Leisure Swimmer’s Edge 18

  • Page 1 SWIM SPAS OWNER’S MANUAL MODELS: SWIMMER’S EDGE 18, DUAL ZONE 18, SWIMMER 18, SWIMMER 14 Premium Leisure, LLC 6101 45 St. N. St. Petersburg, FL 33714 727.573.9611 www.PremiumLeisure.com Part Number 7068 Revised 03/10...
  • Page 2 Owner’s Information Dealer: Date Purchased: __________________________ Company: __________________________ Address: __________________________ Telephone: __________________________ Installer: Date Installed: __________________________ Company: __________________________ Address: __________________________ Telephone: __________________________ Swim Spa: Date Delivered: __________________________ Model: __________________________ Color: __________________________ Serial Number: __________________________ Your unique swim spa serial number is located on a data plate outside the cabinet at ground level.

  • Page 3: Table Of Contents

    Printed in the U.S.A. Version 1.1 Revised 03/10 Part # 7068 Copyright © 2010, Premium Leisure LLC. All rights reserved. No portion of this manual may be reproduced in any manner ™ ™ without express written permission of Premium Leisure LLC. Premium Leisure Swim spas and Thermazone trademarks of Premium Leisure LLC.

  • Page 4: Introduction

    I n t r o d u c t i o n ™ Your choice of a Premium Leisure brand swim spa from Premium Leisure LLC indicates that you are devoted to excellence. The management and staff appreciate your patronage and takes pride in the tradition of quality swim spas that our company represents.

  • Page 5: Important Safety Information

    I m p o r t a n t S a f e t y I n f o r m a t i o n IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Your physiological response to hot water depends on subjective factors such as age, health, pregnant women, temperature sensitivities, chemical sensitivities, and medical history.
  • Page 6 Warnings TO REDUCE THE RISK OF INJURY: The water in a spa should never exceed 40˚C (104˚F). Water temperatures between 38˚C (100˚F) and 40˚C (104˚F) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

  • Page 7: Save These Instructions

    Warning Sign Warning Sign Must Be Posted – The red WARNING sign like the one shown is packed with your new swim spa. This sign must be posted in a prominent place in close proximity to the swim spa installation site immediately upon completion of swim spa installation.
  • Page 8 Basic Safety Guidelines Your swim spa is meant to be enjoyable, healthful, and relaxing. Below are some basic safety guidelines to follow every time you use your swim spa. Always check the temperature of your swim spa before entering. High water temperatures can be hazardous to your health.

  • Page 9: Site Selection And Installation (Electrical Connections)

    This forms a box or “crib/vault” where the swim spa is placed. After excavating the installation site for your Premium Leisure swim spa, ensure that the soil underlying the foundation is capable of...
  • Page 10 support equipment or structure. Install protective waterproof conduit to house light, or topside control cables that must be buried. Access for future service must be considered at the time of design and installation. Difficult access can result in supplemental service labor charges not covered by the factory warranty.
  • Page 11 Electrical Specifications Important – Qualified and licensed electricians must perform all electrical hookups. The following specifications must be followed in order to ensure proper performance and safety. WARNING: Starting an incorrectly wired swim spa could cause severe damage to the mechanical equipment or even bodily harm. Have your licensed electrician verify GFCI (or RCD) wiring with the diagrams on pages 10-15 prior to starting the swim spa or call the technical support line at 727.573.9611.
  • Page 13 Figure 5 – Electrical Service for all models (Swimmer’s Edge 18, Dual Zone 18, Swimmer 18 and Swimmer 14). Single-phase 240V domestic version See wire size chart on page 9. Page 11 For HELP, call 727.573.9611...
  • Page 14 Figure 6 – Electrical Service for all models (Swimmer’s Edge 18, Dual Zone 18, Swimmer 18 and Swimmer 14). Single Service, 1x32A, export version All wiring is 3x4 mm , solid copper See wire size chart on page 9. Note: DIP switch A2 MUST BE OFF. Page 12 For HELP, call 727.573.9611...
  • Page 15 Figure 7 – Electrical Service (Dual Service, 2x16A) for Dual Zone 18, Swimmer 18 and Swimmer 14 export models All wiring is 5x1.5 mm , solid copper See wire size chart on page 9. Note: DIP switch A2 MUST BE ON. Page 13 For HELP, call 727.573.9611...
  • Page 16 Figure 8 – Electrical Service (Three Phase, 3x16A) for Dual Zone 18, Swimmer 18 and Swimmer 14 export models All wiring is 5x1.5 mm , solid copper See wire size chart on page 9. Note: DIP switch A2 MUST BE ON. Page 14 For HELP, call 727.573.9611...
  • Page 17 U.S./Can. Wiring (Dual Zone 18, Swimmers 14/18 – Swim Side) Figure 9 – Wiring Diagram for Dual Zone 18, Swimmer 18 and Swimmer 14 models with PEL2KM3 Control Pack (Swim Side) Page 15 For HELP, call 727.573.9611...
  • Page 18 Page 16 For HELP, call 727.573.9611...
  • Page 19 Export Wiring (Dual Zone 18, Swimmer 14 & 18 – Swim Side) switch positions on P. 21 Figure 10 – Wiring Diagram for Dual Zone 18, Swimmer 18 and Swimmer 14 models with HSEX2000 Control Pack (Swim Side) See wire size chart on page 9. Page 17 For HELP, call 727.573.9611...
  • Page 20 Figure 11 –Board Diagram for Dual Zone 18, Swimmer 18 and Swimmer 14 models. Export (220-240V) version with HSEX2000 Control Pack. Page 18 For HELP, call 727.573.9611...
  • Page 21 U.S. and Canada Wiring (All Models – Spa Side) Page 19 For HELP, call 727.573.9611...
  • Page 22 Figure 13 – Board Diagram for all models Single-phase 240V Domestic version Page 20 For HELP, call 727.573.9611...
  • Page 23 Export Wiring (Dual Zone 18, Swimmer 14 & 18 – Spa Side) Figure 14 – Export Wiring Diagram for Dual Zone 18, Swimmer 18 and Swimmer 14 for GS510SZ Control Pack (See wire size chart on Pg. 9) Page 21 For HELP, call 727.573.9611...
  • Page 24 Figure 15 – Board Diagram for all models Export version for GS510SZ Control Pack. Figure 16 – Panel Button Positions for Dual Zone 18, Swimmer 18 and Swimmer 14 Models Export version Page 22 For HELP, call 727.573.9611...

  • Page 25: Startup

    S t a r t u p Important – Read these step-by-step startup procedures before starting your swim spa. Failure to follow any of these steps listed may result in damage to the equipment and may void your warranty. Note: If you are unsure of any of the above startup procedures, please call our customer care center at 727.573.9611.
  • Page 26 Before Adding Water Before adding water, go through these simple steps now to prevent common issues when setting up your swim spa for the first time. Verify that the following have all been rechecked. Turn off all power to the swim spa at the main breaker panel.
  • Page 27 Remove the fill cap lid located on the top of the tank. Pour fluid in the tank until the sight glass is completely filled. (NOTE: USE ONLY THE FLUID PROVIDED BY PREMIUM LEISURE). Fluid will be blue. Once full, tighten the fill cap.
  • Page 28 Turn the power on at the main breaker. The LED display will show two red lights. Using the handheld remote control (see page 40), press t ON/OFF button. The system will come on and the LED readout will automatically go to 50. Let the system run for 2-3 minutes to pressurize itself.
  • Page 29 mperature the first time you fill your swim spa. ote: The hydraulic hoses should be changed every year. Balancing the Swim Spa Water Using a water test kit (if one was not provided, please call 877.530.PARTS) test for chlorine, pH, total alkalinity, etc. (You may also take a sample of your water to our local pool dealer.) Follow all instructions with the test kit and take notes accordingly.
  • Page 30 Only if pushing this button successfully trips this circuit breaker should you reset this breaker and proceed to the next step. Go to the topside control panel. The swim spa first goes into a 6-minute Priming mode, indicated by “Pr” message. Water heating is disabled during priming.
  • Page 31 DANGER: If this breaker does not trip, immediately call your electrician. Do not use your swim spa! Only if pushing this button successfully trips this circuit breaker should you reset this breaker and proceed to the next step. Go to the topside control panel. The spa side of the unit first goes into a 6-minute Priming mode, indicated by “Pr”...

  • Page 32: Water Balancing

    W a t e r B a l a n c i n g Note: Perform water balancing weekly and whenever you change water (or when the swim spa is first filled) to ensure proper water condition. Once your swim spa reaches 95ºF, use our Bromine Test Strips (not included) and add the necessary chemicals (not included) to stabilize your water chemistry.

  • Page 33: Topside Controls And Operation

    T o p s i d e C o n t r o l s & O p e r a t i o n Swimmer’s Edge 18, Dual Zone 18, Swimmer 18 & Swimmer 14 - Spa Side (MVP 260 Domestic) Figure 21–...
  • Page 34 needed (depending on mode). When the low speed turns on automatically, it cannot be deactivated from the panel, however the high speed may be activated. Light Press the “LIGHT” button once to turn on your swim spa lights. Press the LIGHT button multiple times to cycle through the many available color patterns.
  • Page 35 Swimmer’s Edge 18, Dual Zone 18, Swimmer 18 and Swimmer 14 - Spa Side (Export VL600S) The topside control panel operates and programs your swim spa. Basic button functions are described next. Figure 22 – Topside Callouts for VL600S Controls Initial Start Up When your swim spa is first actuated, it will go into Priming mode, indicated by “Pr.”...
  • Page 36 15 minutes and the low speed of Pump 1 automatically will turn off after 4 hours. The low speed of Pump 1 runs when the “AUX” Pump 2 (if equipped) is on. It may also active for at least two minutes every half hour to detect the swim spa temperature and then to heat to the set temperature if needed (depending on mode).
  • Page 37 Smart Winter Mode If the system (sensor located inside heater) detects ambient conditions below 44ºF/6.7ºC, it automatically enters the Smart Winter Mode for period of four minutes after it detects the swim spa temperature has risen to 45ºF/7.2ºC. Programming Summary Figure 24 –...
  • Page 38 Dual Zone 18, Swimmer 18 and Swimmer 14 - Swim Side (ML700 Domestic and Export) Figure 23 – ML700 Topside Control Panel Control Panel Legend Heat icon: Indicates different stages of heating Jets icon: Spins fast on high speed; spins slow on low speed Light icon: Light is on/off F1, F2 indicators: Filter cycle 1 or 2 will be illuminated PL, TL indicators: Locking Panel or Set Temperature will be illuminated...
  • Page 39 to prevent the spa water from becoming stagnant in the plumbing and air lines and improve skimming action to remove debris and suspensions from the water surface. In addition, the programmable filtration cycle (start/end) times of each cycle will designate the start and end time where the heater is allowed to operate in economy and sleep modes.
  • Page 40 Circulation Pump Operation Your system is equipped with a circulation pump. The circulation pump provides 24-hour continuous water circulation and filtration. It works like this: a dedicated, energy efficient circulation pump constantly draws water from the spa, runs it through the filter and the heater (heating only when necessary), then back to the spa.
  • Page 41 Freeze Protection If the temperature sensor detects a temperature drop to 44 F (6.7 C) within the heater, then the pump automatically activates to provide freeze protection. The equipment stays on until four (4) minutes after the sensors detect that the spa water temperature has risen to 45 F (7.2 C) or higher.
  • Page 42 Swimmer’s Edge 18 - Swim Side (Turbine Propeller, All Units) When you are ready to swim in the Swimmer’s Edge 18 Swim Spa, press the “ON/OFF” button on the waterproof remote control. Your digital readout will default to the No. 50. Increase to your desired swim speed by pushing the “FAST”...

  • Page 44: Cover

    Using the Built-in MP3 Docking Station and Speakers Figure 27 – Optional MP3 Docking Station with Jack If equipped, simply plug in your MP3 player, push play and select your desired volume. Your favorite music is amplified through a built-in subwoofer (underneath your swim spa) and is heard through the speakers.

  • Page 45: Frequently Asked Questions

    Grip handle barrier Aluminum channel Polystyrene seam stoppers Heat-sealed insulation 10. Reinforced edges Chemical-resistant vapor 11. Breathable underside material Use the lock-down tabs to prevent access to the swim spa by children and to prevent the wind from lifting the cover off. Figure 29 - Lockdown Tabs Sitting, standing, and snow buildup on the cover will break the cover.
  • Page 46 Figure 31 - Bleeding Air What happens when my warranty expires? Premium Leisure will continue to provide service for your swim spa after your warranty has expired via our customer care center at 727.573.9611. Where can I get more Chemicals or other accessories? Visit www.hottubparts.com...

  • Page 47: Troubleshooting

    Caution: Do not turn off too many jets at the same time. This can create backflow and possible damage to your swim spa! Do not attempt to adjust the oval jets on the swim side of the unit. Are the spa jets removable? Interchangeable? Replaceable? Most spa jets are made removable and adjustable for customized hydrotherapy.
  • Page 48 PROBLEM CAUSE SOLUTION Moved my Wiring error at Check Neutral wiring of GFCI (see diagrams swim spa and GFCI on pages 10-22) now it doesn’t No power to Reset circuit breakers on GFCI panel and work swim spa main circuit breaker panel Nothing Breaker has Check and reset breaker.
  • Page 49 MESSAGE MEANING ACTION REQUIRED Potential freeze condition No action required. The pump will detected (Ice) automatically operate regardless of the swim spa status. Sensor A is not working Check the sensor "A" plug correctly. Swim spa is shut connection to circuit board. The down.

  • Page 50: Maintenance And Care

    MESSAGE MEANING ACTION REQUIRED When the swim spa is first The Priming mode runs for up to activated, it goes into four minutes and then the swim spa Priming mode. begins to heat and maintain the water temperature in Standard mode.
  • Page 52 Shutdown / Winterizing Your Premium Leisure swim spa is designed to operate year round. If you plan to leave your swim spa unused for long periods of time in severely cold weather, you should winterize your swim spa to avoid accidental freezing due to a power or equipment failure.
  • Page 53 WARNING: NEVER use paint solvents, acids, acetone, benzene, lacquer thinner, tolulene, xylene, or similar chemicals to clean your swim spa shell. Water Management Our chemical water purification system is a perfect match for your swim spa. Depending on usage, the water in your swim spa should be changed every 6-12 months.

  • Page 54: Specifications

    S p e c i f i c a t i o n s SWIMMER’S EDGE 18 (MODEL 2030) *Specifications are subject to change without notice. For export (overseas) part numbers, please call 727.573.9611. For export (overseas) electrical rating, see the chart on page 9. Page 52 For HELP, call 727.573.9611...
  • Page 55 Swimmer’s Edge 18 Specifications* Dimensions 213” (541 cm) L x 89” (226 cm) W x 58”147 (cm) D Therapy Seats Water Jets Capacity 2,400 USG /9,085 L Dry Weight 2,750 Lbs/1,247 Kg Filled Weight 22,778 Lbs/10,332 Kg Electrical 240VAC 40A 60Hz (Swim Side) 240VAC 32A 60Hz (Spa Side) GFCI 50A (Swim Side) and 40A (Spa Side) Figure 33 –...
  • Page 56 DUAL ZONE 18 (MODEL 2022) *Specifications are subject to change without notice. For export (overseas) part numbers, please call 727.573.9611. For export (overseas) electrical rating, see the chart on page 9. Page 54 For HELP, call 727.573.9611...
  • Page 57 Dual Zone 18 Specifications* Dimensions 213” (541 cm) L x 89” (226 cm) W x 58”147 (cm) D Therapy Seats Water Jets Capacity 2,100 USG /7,949 L Dry Weight 1,900 Lbs/862 Kg Filled Weight 19,424 Lbs/8,811 Kg Electrical 240VAC 48A 60Hz (Swim Side) 240VAC 32A 60Hz (Spa Side) GFCI 60A (Swim Side) 40A (Spa Side) Figure 35 –...
  • Page 58 SWIMMER 18 (Model 2028) *Specifications are subject to change without notice. For export (overseas) part numbers, please call 727.573.9611. For export (overseas) electrical rating, see the chart on page 9. Page 56 For HELP, call 727.573.9611...
  • Page 59 Swimmer 18 Specifications* Dimensions 213” (541 cm) L x 89” (226 cm) W x 58”147 (cm) D Therapy Seats Water Jets Capacity 2,400 USG /9,085 L Dry Weight 1,900 Lbs/862 Kg Filled Weight 19,424 Lbs/8,811 Kg Electrical 240VAC 48A 60Hz (Swim Side) 240VAC 32A 60Hz (Spa Side) GFCI 60A (Swim Side) 40A (Spa Side) Figure 37 –...
  • Page 60 SWIMMER 14 (Model 2021) *Specifications are subject to change without notice. For export (overseas) part numbers, please call 727.573.9611. For export (overseas) electrical rating, see the chart on page 9. Page 58 For HELP, call 727.573.9611...
  • Page 61 Swimmer 14 Specifications* Dimensions 170” (432 cm) L x 91” (231 cm) W x 50”127 (cm) D Therapy Seats 3 (With Lounge) 4 (Without Lounge) Water Jets 28 (With Lounge) 29 (Without Lounge) Capacity 1,600 USG /6,057 L Dry Weight 1,605 Lbs/728 Kg Filled Weight 14,958 Lbs/6,785 Kg...

  • Page 62: Certificate Of Verification

    W a r r a n t y...
  • Page 63 6101 45 St. N. St. Petersburg, FL 33714 727.573.9611 www.PremiumLeisure.com...

This manual is also suitable for:

Swimmer 18Dual zone 18Swimmer 14

Table of Contents