Page 1
INSTALLATION AND SERVICE INSTRUCTIONS Keep this booklet for future reference. The dryer must be fitted by a competent person. In the U.K. Registered Installers undertake to work to safe and satisfactory standards. The dryer must be installed in accordance with the Gas Safety (Installation and Use) Regulations 1998.
TECHNICAL DATA GAS CONTROL Type: Pactrol full sequence flame control, P16A GTD(CE) 414601. Ignition electrode gap to burner 3 to 4mm Flame GENERAL failure electrode (4213 078 52641). Height from heater Front loading resistance sensing tumble dryer with gas base to centre of electrode 27.0±0.5mm. heating.
INSTALLATION 1 INSTALLATION 5 POSITION OF DRYER AND CONNECTIONS The dryer is designed for installation using a flexible gas connection with tubing in accordance with B.S. 669. Ensure that the supply gas sizing is adequate. When installing, position the appliance so that the plug is Y = 150 to 330 mm accessible.
Page 5
6. OPERATIONAL CHECK AIRFLOW 6.1 Remove the pressure test point screw from the gas It is most important that airflow to the plinth is not tee connection at the back of the dryer and connect restricted. a gas pressure gauge. MAINTENANCE 6.2 Check that the selector switch is set to 'Extra dry', This appliance does not require an annual service...
SERVICE INSTRUCTIONS PROGRAMME RECOMMENDATIONS FOR DISMANTLING Note: Re-assembly should be done in reverse The electronic control measures dryness by the electrical sequence to these instructions. resistance method and operates relays to: a) energise the drive motor, in foward and reverse rotation and b) TOP ACCESS energise the full sequence flame controller.
Page 7
the Fan Access Cover (447) and the back of the Banjo HEATER ASSEMBLY REMOVAL Assy (440). From underneath the dryer withdraw the 4- Heater Assy. (32), Solenoid Coil (45 or 45A), Flame screws (396) securing the Motor Bracket (432) to the failure Electrode (33), lgnition Electrode (39).
Page 8
REAR ACCESS UPPER securing the Micro-Switch Assy. - See TOP ACCESS. Rear Seal Assy. (14), Drive Belt (125), Drum (266), Lay the dryer on its back. Drum Shaft and Bearing (270). Withdraw the 2-screws securing the plinth (199) to the Remove the table top assembly (386) and disconnect the Cabinet, unhook the plinth fixings and remove it.
FAULT FINDING In the event of an electrical fault carry out the preliminary electrical system checks i.e. earth continuity, polarity, and insulation resistance. Use each chart to locate the fault causing the dryer to operate incorrectly as follows: Chart No. 1 Motor does not run.
Page 10
Chart 1. Motor does not run START Is electrical continuity across both live and neutral paths of R.F.I. filter? Exchange R.F.I. filter, does motor start? Check door closed, timer ON electrical supply ON Correct as necessary does motor start? Is voltage between L and N on Input terminal 230V? Check fuse and mains cable for continuity, does motor start?
Page 11
Chart 2. Motor runs but full sequence control does not produce ignition spark START With machine ON (30 min) is voltage between output HE on controller and TB-N 230v? Exchange sensing controller, Does gas control spark? Does control spark with high heat selected? Does control spark with low heat selected?
Page 12
Chart 3. Motor runs Full Sequence Control produces ignition sparks, but gas does not ignite...
Page 13
Chart 4. Motor runs, gas ignites but stays on for only short period Before proceeding, ensure polarity of 13 Amp supply socket and earthing is correct. Start Is weight of load suitable? Is filter clean? Is vent hose or terminal unobstructed? Is vent terminal unaffected by wind conditions that may...
BG83A_ (Eco 83A) PARTS LIST Item Description Part Number Expl. View Control Unit 4213 092 25451 Control Unit Bracket Assembly 4213 070 08623 Screw M4 x 10 8213 130 37161 2&5 Rear Seal Assembly 4213 092 08511 External Feed Pipe (Bundy Tube Assy 3)
Page 21
BG83A_ (Eco 83A) PARTS LIST Control Panel Assembly 4213 092 51881 Locator Peg 4213 077 61281 6G*3/8 DP/PWABE/NIBS/TSZPC 8213 130 38051 Hinge Assembly 4213 092 26071 Window 4213 077 4409_ Door Frame 4213 077 92271 Latch Pivot 4213 075 13013...
Need help?
Do you have a question about the ECO 83A and is the answer not in the manual?
Questions and answers