Quadra-Fire SANTAFEI-MBK Owner's Manual page 2

Santa Fe Pellet Insert
Hearth & Home Technologies welcomes you to our tradi-
tion of excellence! In choosing a Quadra-Fire appliance,
you have our assurance of commitment to quality, durabil-
ity, and performance.
This commitment begins with our research of the market,
including 'Voice of the Customer' contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world's most
advanced technology to achieve the optimum operation of
SANTA FE PELLET INSERT
SERIAL NO. / NUMÉRO DE SÉRIE
007015
2011 2012 2013
JAN FEB MAR APR
JULY AUG SEPT OCT NOV DEC
O-T L Portland
Tested and
Listed by Oregon USA
Report / Rapport: 061-S-77d-6.2
C US
OMNI-Test Laboratories, Inc.
U.S. ENVIRONMENTAL PROTECTION AGENCY
This model is exempt from EPA certification under 40 CFR
60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
Made in China/ Fait Aux Chine
SAMPLE:
SERIAL NUMBER LABEL
LOCATION:
Behind left access panel.
Page 2
and Welcome to the Quadra-Fire Family
R
Black letters on silver
background, adhesive
back.
Size: 2.875" w x 3.25" h
MAY JUNE
7019-222C
7019-221D
!
our stoves, inserts and fireplaces. And yet we are old-fash-
ioned when it comes to craftsmanship. Each unit is meticu-
lously fabricated and surfaces are hand-finished for lasting
beauty and enjoyment. Our pledge to quality is completed
as each model undergoes a quality control inspection.
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
O-T L Portland
Tested and
Oregon USA
Listed by
C US
OMNI-Test Laboratories, Inc.
Santa Fe Pellet Insert-MBK
Report No.
#061-S-77d-6.2
Input Rating: 30,000 BTU/HR.
Electrical Rating: 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS.
Listed Solid Fuel Room Heater/Pellet Type Insert. Also suitable for Mobile Home Installation. This appliance has been tested
and listed for use in Manufactured Homes in accordance with OAR 814-23-9000 through 814-23-909.
Tested to: ASTM E-1509-2004, ULC S628-93, ULC /ORD-C1482-M1990 Room Heating Pellet Burning Type, (UM) 84-HUD FOR
USE ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN FUEL. Do not use any other type of fuel. OMNI-Test Laboratories,
Inc. has determined that this appliance complies with Canadian Standards Association (CSA) B415.1 and Title 40 of the
U.S. Code of Federal Regulations, Part 60, SubPart AAA.OMNI-Test Laboratories Accrediations: The Standards
Council of Canada, the American National Standards Institute, and the U.S. Environmental Protection Agency.
Route power cord away from unit. Do not route cord under or in front of appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing. Replace glass only with 5mm ceramic available
from your dealer.
To start, set thermostat above room temperature, the appliance will light automatically. To shutdown, set thermostat to below room
temperature. For further instruction refer to owner's manual.
KEEP VIEWING AND ASH REMOVAL DOORS TIGHTLY CLOSED DURING OPERATION.
PREVENT HOUSE FIRES
Install and use only in accordance with manufacturer's installation and operating instructions. CONTACT LOCAL BUILDING
OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
WARNING - FOR MOBILE HOMES: Do not install appliance in a sleeping room. An outside combustion air inlet must be
provided. The structural integrity of the mobile home floor, ceiling and walls must be maintained.
Refer to manufacturer's instructions and local codes for precautions required for passing chimney through a combustible wall
or ceiling. Inspect and clean vent system frequently in accordance with manufacturer's instructions.
Do Not Connect This Unit to a Chimney Serving Another Appliance.
Use a 3" or 4" diameter type "L" or "PL" venting system.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
A
C
B
C
0 in. Clearance To Exposed Section And Face Trim
Max. Mantel Depth: 12 in. (305mm)
MANTEL
Face Trim
B
C
A
D
E
F
DO NOT REMOVE THIS LABEL
SAMPLE: CLEARANCE TO COMBUSTIBLES LABEL
LOCATION: On chain behind right access panel
SAFETY LABEL
Manufactured by:
R
1445 Highway North, Colville, WA 99114
www.quadrafire.com
AS A BUILT-IN UNIT
D
A Top of Hopper Top Vent
Rear Vent
B
B Side of Hopper Top/Rear Vent 2.0 in. 51mm
C Back of Hopper Top/Rear Vent 2.5 in. 64mm
D Vent Pipe to Combustible Top/Rear Vent 3.0 in. 76mm
Masonry or Zero Clearance
A Insert side to combustible side wall 16 in.
B Insert top to mantel 12 in.
C Insert top to max. 2.25 in. to top face trim 4.75 in.
D Insert side to max. 2.25 in. to side face trim
10 in.
E Hearth extension to from door opening - front 6 in .
F Hearth extension from side of door opening
6 in.
*When constructing floor protection for your pellet appliance, any
parts or materials used, must be non-combustible.
January 21, 2013
R
2.0 in. 51mm
2.5 in. 64mm
406mm
305mm
121mm
254mm
152mm
152mm
7019-223D