Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Datatool S4
Summary of Contents for Datatool S4
- Page 1 USER GUIDE...
- Page 2 Datatool ® you, that the more difficult you make your machine Tagging Upgrade Kit, only available to S4 security to be stolen, the lower the potential risk. Applying system owners, which brings the parts marking up common sense each time you park and securing to insurance standards at an enhanced price.
- Page 3 The pictures below show the type of transmitter Should you require a combined ignition key and supplied with your alarm depending on the type remote control for the S4 Yellow, it is possible to purchased. purchase the S4 Red remote control and code it to the Yellow type alarm.
- Page 4 Changing your remote control battery Models S4 Red and S4 Green Each remote control contains a single long-life lithium battery (CR1616). This battery will normally last at least 12 months. Normal range for the remote control is around 10 metres. As the battery within...
- Page 5 The S4 Yellow transmitter contains a single CR2032 Lithium battery. This battery will normally last at least 24 months. (See S4 Red and Green for range and its reduction with age). 1. Use a small coin, placed in the recess between the two case halves near the key attachment hole, to split the casings.
- Page 6 (except If you wish to make the alarm fully arm passively you on the S4 Green model) 45 seconds after turning off can do this via the software switches covered within the ignition.
- Page 7 The system will still have immobilised the machine including PIR’s, coded into the system. This ensures (except with S4 Green model) and the alarm will you will always know you are in possession of all react if the machine is hot-wired, the supply to the remote controls capable of operating your system.
- Page 8 NOTE: The inclusion of the arm and disarm indication from PIR sensor beeps is strictly forbidden in all EU countries. NOTE: The S4 Yellow product uses the shock sensor for movement detection and is equipped with only the potential for trigger switch 1 and no trigger switch 2.
- Page 9 - The LED is turned OFF is left connected to a float charger suitable for - The Siren Beep is turned off maintaining the condition of the battery without damaging it, such as the Datatool ® Battery - The internal battery back-up is turned off Conditioner (Pt No.
- Page 10 Thatcham approved Datatool ® Python We would again advise you on the benefits of using Lock and Chain system combined with a Datatool ® the Datatool ® Battery Conditioner (Pt No. 02012011) Fortress Ground Anchor.
- Page 11 PIN number know (or have not entered) your PIN number, the by entering it again. alarm system will have to be returned to Datatool ® 10. Turn the ignition ON and repeat the above to be recoded.
- Page 12 PIN and you will know the PIN, the system will have to be returned have to re-enter your preferred number. to Datatool ® for recoding and 2 new remote controls. This is a chargeable service.
- Page 13 Disarming the system with your PIN If the transmitter is lost or damaged, or the If entered correctly, the alarm will disarm and the transmitter battery is flat, the system can be motorcycle indicators will flash once. overridden by your chosen four digit PIN (Personal NOTE: As soon as the alarm system is disarmed, the Identification Number) used in conjunction with the passive arming alarm (if selected) and passive...
- Page 14 Lost or stolen remote controls can be removed from d) Enter the PIN number as previously described. your system by any APPROVED Datatool ® dealer. e) When the PIN number has been entered correctly,...
- Page 15 Customising the system It is possible to change the operation of the security 2. Press the BLACK button on the remote control to system to suit your requirements (see transmitter move backwards through the table to Switch 1 learn procedure for details on how to enter the (one beep will be heard when the switch is software switches).
- Page 16 If the alarm system has been armed, the internal Press GREY button battery back-up system (S4 Red and Green only) is also turned on and disconnection of the battery will cause the alarm system to sound.
- Page 17 Default setting level 8 Arm / Disarm Tones On/Off Panic On/Off Nudge sensor (S4 Red and S4 Green) On continuous warn-away with no trigger Trigger on first nudge detection 1 Warn-away and trigger on second nudge 2 Warn-aways and trigger on third nudge...
- Page 18 PIR sensor instead of to the If you wish only to protect the doors and windows of machine. The sensor will then trigger the alarm the garage you can use the Datatool ® garage security system through its radio link.
- Page 19 • Do not mix batteries. Replace all batteries at the The declaration of conformity certificates applicable same time with new batteries of same system and to the Datatool S4 range of security systems can be manufacture. viewed at www.datatool.co.uk/product • Clean contacts on the battery and the equipment Contacts before inserting new ones.
-
Page 20: Quick Reference Guide
To turn off press BOTH buttons again ‘Ferry Mode’ Press BLACK button within 10 seconds of arming the alarm fully For full instructions on features please refer to the main manual or visit www.datatool.co.uk...
Need help?
Do you have a question about the S4 and is the answer not in the manual?
Questions and answers
Hi. I have a bike which got unplugged from the t/charger causing a flat battery. The battery for the bike is ok now but the alarm initially kept going off then set,or so it seems. The alarm is not showing arming or disarming now. My bike can be started and the flashy light on the fob is working. Pls help?
To troubleshoot the Datatool S4 alarm system that is not showing arming or disarming after a flat battery:
1. Check the Fuses – Ensure all motorcycle fuses, including the alarm fuse, are intact.
2. Reset the Alarm – Disconnect the alarm system and reconnect it to reset.
3. Check the Wiring – Ensure all alarm connections are secure and no wires are damaged.
4. Use a Battery Conditioner – If the battery was disconnected, using a Datatool battery conditioner can help maintain the charge.
5. Check Ignition Sense – If the alarm does not respond even with ignition ON, verify that the alarm unit is receiving ignition sense.
6. Verify Kill Switch Position – Ensure the kill switch is in the ON position.
7. Reinstall Indicators Properly – If indicators were changed, ensure correct wiring to avoid alarm malfunction.
If the issue persists, contact your dealer for further assistance.
This answer is automatically generated