Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datatool DT202
Summary of Contents for Datatool DT202
- Page 1 DT202 Operating Instructions Revision 1 24-07-2023 Copyright © 2023...
-
Page 2: Table Of Contents
To adjust the passive arming time Page 9 -10 To choose the motorcycle battery type Page 10 To reset the DT202 to the default settings Page 10 To add a new remote control Page 11 Technical Specification, F.A.Q. and Warranty... -
Page 3: Dt202 Operating Guide
Datatool reserves the right to amend the information at any time without notice. Insurance Approval The DT202 is approved in the UK as a Thatcham Category 2-1 alarm/immobiliser, designed to be installed on all 12-volt motorcycles that have a Thatcham accredited alarm or immobiliser whether O.E or aftermarket. -
Page 4: The Remote Control
DT202 Operation Guide Revision 1 24-07-2023 The Remote Control The DT202 is provided with 2 remote controls as standard. It is possible to add up to 4 extra remote controls (6 in total). We recommend making use of both remote controls from time to time, ideally alternating use every 3 to 6 months. -
Page 5: Operating The Dt202 Basic Functions
10 seconds whilst the system initializes the tilt sensor and trigger inputs. After 10 seconds, the DT202 is fully armed, and the motorcycle LED will flash at a rate determined by the motorcycle battery voltage (see Battery Monitoring). -
Page 6: Operating The Dt202 Advanced Features
Battery Monitoring Arm Silently If the arm/disarm tones are enabled, it is possible to arm the DT202 silently by pressing the Programming Button on the remote immediately before pressing the Arm/Disarm button. The buttons must be pressed within 3 seconds of each other, the DT202 will arm as normal except the arming notification tones will not be sounded. -
Page 7: Long Term Storage Mode
To exit Long Term Storage Mode, turn the motorcycle ignition on the motorcycle indicators will start to flash and the DT202 will sound a series of fast bleeps that rise in volume. Press the Arm/Disarm button to disarm the DT202. If the Arm/Disarm button is not pressed the DT202 will trigger fully and the siren will sound. -
Page 8: Bike Finder
If the DT202 is disarmed with ignition off, then pressing and holding the Arm/Disarm button for 3 seconds will first arm the DT202 before triggering the Panic Alarm. If the DT202 is in the armed state, then pressing and holding the Arm/Disarm button for 3 seconds will disarm the DT202 before triggering the Panic Alarm feature. -
Page 9: Optional Supplementary Siren Output
Optional Supplementary Siren Output The DT202 allows for the addition of an optional second siren using the Optional Supplementary Siren Output, if used with a suitable siren this can increase the output volume when the alarm is sounding. -
Page 10: Diagnostics
DT202 Operation Guide Revision 1 24-07-2023 Diagnostics When the DT202 is disarmed via a remote control, a long chirp is given followed by a series of short chirps signifying the DT202 has been triggered. The diagnostic code can be repeated by switching the ignition on and off, unless the alarm has been rearmed or the ignition has been switched on for 60 seconds or more at which point the code will be erased. -
Page 11: To Adjust The Arm/Disarm Tone
Turn off the ignition to exit programming and save the new setting a loud chirp will be given. If the ignition is not switched off within 30 seconds the DT202 will give a loud chirp and the currently selected setting will be stored. -
Page 12: To Choose The Motorcycle Battery Type
Turn off the ignition to exit programming and save the new setting a loud chirp will be given. If the ignition is not switched off within 30 seconds the DT202 will give a loud chirp and the currently selected setting will be stored. -
Page 13: To Add A New Remote Control
Within 10 seconds, press and hold both buttons on the remote control. After 3 seconds the DT202 will start to chirp. Release the remote control buttons after six chirps, if you miss the correct chirp wait for the alarm to exit programming mode after the seventh chirp or turn off the ignition a loud chirp will be given to indicate programming has been exited. - Page 14 Warranty Datatool DT202 is provided with a comprehensive 2-year warranty in addition to your statutory rights, designed to combat any material or manufacturing defects which become apparent within 2 calendar years from the date of first installation. In the unlikely event of repairs being required under the provided warranty, please contact the installing dealer for assistance.