Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datatool DT201
Summary of Contents for Datatool DT201
- Page 1 DT201 Operating Instructions Revision 1 24-07-2023 Copyright © 2023...
-
Page 2: Table Of Contents
To adjust the passive arming time Page 10 To choose the motorcycle battery type Page 11 To reset the DT201 to the default settings Page 11 To add a new remote control Page 11 - 12 Technical Specification, F.A.Q. and Warranty... -
Page 3: Dt201 Operating Guide
DT201, but the motorcycle indicators will not flash. The siren will operate for 29 seconds, then re-arm. This will be repeated 10 times if the alarm trigger remains. After the activation cycle has been repeated 10 times the siren will no longer sound on that circuit until the next alarm arm/disarm, all other circuits remain active though. -
Page 4: The Remote Control
DT201 Operation Guide Revision 1 24-07-2023 The Remote Control The DT201 is provided with 2 remote controls as standard. It is possible to add up to 4 extra remote controls (6 in total). We recommend making use of both remote controls from time to time, ideally alternating use every 3 to 6 months. -
Page 5: Operating The Dt201 Basic Functions
10 seconds whilst the system initializes the tilt sensor and trigger inputs. After 10 seconds, the DT201 is fully armed, and the motorcycle LED will flash at a rate determined by the motorcycle battery voltage (see Battery Monitoring). -
Page 6: Passive Immobilisation
To disarm the alarm system with the two-button remote press the Arm/ Disarm button once on the remote control the indicators on your motorcycle will flash once to confirm the DT201 has disarmed and if the audible chirps are enabled, a single chirp will be heard. -
Page 7: Arm/ Disarm Silently
DT201 Operation Guide Revision 1 24-07-2023 Arm Silently If the arm/disarm tones are enabled, it is possible to arm the DT201 silently by pressing the Programming Button on the remote immediately before pressing the Arm/Disarm button. The buttons must be pressed within 3 seconds of each other, the DT201 will arm as normal except the arming notification tones will not be sounded. -
Page 8: Bike Finder
To exit Long Term Storage Mode, turn the motorcycle ignition on the motorcycle indicators will start to flash and the DT201 will sound a series of fast bleeps that rise in volume. Press the Arm/Disarm button to disarm the DT201. If the Arm/Disarm button is not pressed the DT201 will trigger fully and the siren will sound. -
Page 9: Battery Monitoring
3 seconds will first arm the DT201 before triggering the Panic Alarm. If the DT201 is in the armed state, then pressing and holding the Arm/Disarm button for 3 seconds will disarm the DT201 before triggering the Panic Alarm feature. If the Arm/Disarm button is pressed a second time to stop the Panic feature the alarm will always reset to the disarmed state regardless of the previous state. -
Page 10: Optional Secondary Trigger
If you would like to use the Optional Secondary Trigger speak to your installing dealer. Diagnostics When the DT201 is disarmed via a remote control, a long chirp is given followed by a series of short chirps signifying the DT201 has been triggered. -
Page 11: Troubleshooting
DT201 again. CAUTION • It is important that the internal battery in the DT201 is not left in a discharged condition. • If the DT201 internal battery is left discharged it will result in damage to the battery. -
Page 12: To Adjust The Automatic Rearm
Turn off the ignition to exit programming and save the new setting a loud chirp will be given. If the ignition is not switched off within 30 seconds the DT201 will give a loud chirp and the currently selected setting will be stored. -
Page 13: To Choose The Motorcycle Battery Type
Turn off the ignition to exit programming and save the new setting a loud chirp will be given. If the ignition is not switched off within 30 seconds the DT201 will give a loud chirp and the currently selected setting will be stored. -
Page 14: Technical Specification, F.a.q. And Warranty
DT201 Operation Guide Revision 1 24-07-2023 Press either button on the first remote control to be added, the DT201 will bleep once and the LED will flash once indicating the number of remote controls programmed. NOTE: After programming the first remote control all other remote controls will be deleted. - Page 15 Warranty Datatool DT201 is provided with a comprehensive 2-year warranty in addition to your statutory rights, designed to combat any material or manufacturing defects which become apparent within 2 calendar years from the date of first installation. In the unlikely event of repairs being required under the provided warranty, please contact the installing dealer for assistance.