Section 11: Reference Material; Component Functions - Quadra-Fire SANTAFE-MBK Owner's Manual

R
11
Reference Materials
A. Component Function
1. Control Box
a. The control box is located on upper right side of
appliance, behind the right side panel and above the
vacuum switch.
b. There is a light located inside of the control box. The
internal light will turn green when the appliance has
reached a temperature of 200
and will turn red when it reaches 600
c. There is also an internal blue light located in the upper
left corner of the control box. When you plug in the
appliance the blue light will automatically start blinking
6 times in a row for 60 seconds and then will stop.
NOTE:
Do NOT open the control box. This will void the
warranty. If you need to plug in or remove the control
box you must fi rst unplug the appliance.
2. Convection Blower
The convection blower is mounted at the bottom rear of the
appliance. There are 2 impellers, one on each side of the
motor. The convection blower pushes heated air through the
heat exchange system into the room.
3. Exhaust Blower
The exhaust blower is mounted on the right side of the
appliance. The exhaust blower is designed to pull the
exhaust from the appliance and push it out through the
venting system.
4. Feed System
The feed system is located on the right side of the appliance
and can be removed as an entire assembly. The assembly
includes the feed motor, mounting bracket, bearing and feed
spring (auger). The hollow feed spring (auger) pulls pellets
up the feed tube from the hopper area and drops them down
the feed chute into the fi repot.
5. Firepot
The fi repot is made of high quality ductile iron and has a
cleaning pull-out rod. The fl oor of the fi repot opens for
cleaning when you pull out the rod. Be sure that the fl oor
returns to a completely closed position or your appliance will
not operate properly.
6. Fuse
The fuse is located on the front of the junction box next to
the red call light. The fuse will blow should a short occur and
shut off power to the appliance.
Page 40

 F (93  C) in the fi repot.
F (315  C).
o
7050-128G
When describing the location of a component,
it is always AS YOU FACE THE FRONT OF
THE APPLIANCE.
7. Heat Exchangers
The heat exchangers transfer hot air from the exhaust system
into convecton air. Remove the stainless steel top baffl e to
access the heat exchangers. There are 2 clean out rods
located under the heat exchangers.
8. Heat Output Switch
The heat output switch is located on the upper right rear panel.
The function of the heat ouput switch is to regulate the burn
rates; low, medium and high settings.
9. Hopper Switch
The hopper switch is located in the upper right hand corner
of the hopper. This switch is designed to shut down the feed
motor whenever the hopper lid is opened.
10. Igniter
The igniter is mounted on the base of the fi repot. Combustion
air travels over the red hot igniter creating super heated air
that ignites the pellets.
11. Junction Box And Wiring Harness
The junction box is located on the right side of the appliance,
behind the right side panel. The junction box and wiring
harness are replaced as one component.
12. Power Supply
The power outlet is located behind the control box on the back
of the appliance, lower left corner. Check the wall receptacle
for 120 volt, 60 Hz (standard current). Make sure the outlet is
grounded and has the correct polarity. A good surge protector
is recommended.
13. Red Call Light
The red call light is on the side of the junction box, next to
the fuse. The function of the red call light is to indicate that
the thermostat is calling for heat.
14. Reset Button
The reset button is located on the back of the appliance in the
upper right corner below the heat output control switch. The
function of the button is to momentarily open the thermostat
circuit, which restarts the system.
15. Thermocouple
The thermocouple is located on top of the fi repot inside
the thermocouple cover (ceramic protection tube). The
thermocouple sends a millivolt signal to the control box
indicating the preset temperatures of the green and red lights
have been obtained.
Santa Fe Pellet Stove
May 12, 2014