1. Manuals
  2. Brands
  3. Zephyr Manuals
  4. Ventilation Hood
  5. ES1-E30AB
  6. Use, care and installation manual

Zephyr ES1-E30AB Use, Care And Installation Manual

Zephyr range hoods use, care and installation guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RANGE HOOD
INSTALLATION INSTRUCTIONS - USE AND CARE
HB0064
MODEL ES1-E30AB, ES1-E30AS, ES1-30AW
!
INTENDED FOR DOMESTIC COOKING ONLY
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: CLEANING AND OPERATION INFORMATION
ON PAGES 9 AND 10.
06683 rev. A
DEC07.0101

Advertisement

Table of Contents
loading

Related Manuals for Zephyr ES1-E30AB

Summary of Contents for Zephyr ES1-E30AB

  • Page 1 RANGE HOOD INSTALLATION INSTRUCTIONS - USE AND CARE HB0064 MODEL ES1-E30AB, ES1-E30AS, ES1-30AW INTENDED FOR DOMESTIC COOKING ONLY READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: CLEANING AND OPERATION INFORMATION ON PAGES 9 AND 10. 06683 rev. A...
  • Page 2 WARNING WARNING TO REDUCE THE RISK OF FIRE, TO REDUCE THE RISK OF INJURY TO ELECTRIC SHOCK OR INJURY TO PERSONS IN THE EVENT OF A RANGE TOP PERSONS, OBSERVE THE FOLLOWING: GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended 1.

  • Page 3: Table Of Contents

    ABOUT THIS MANUAL Please take note this manual uses the following symbols to emphasize particular information: WARNING Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death. CAUTION Denotes an instruction which, if not followed, may severely damage the unit and/or its components.

  • Page 4: Install Ductwork

    1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 6’’ (150 mm) round ducts, use a transition. Use 2’’ (50 mm) duct tape to seal duct joints.

  • Page 5: Prepare The Installation

    3. PREPARE THE INSTALLATION Make sure the following items are included: - Hood - Filters (2) - Adapter/damper assembly 3¼’’ x 10’’ (located inside the hood, under the bottom panel) - Compact fluorescent lamps (120 V, 13 W, PLC13, 2700 K with G24q-1 base) - Bag of parts including: (1) wire clamp, (5) 1/2’’...

  • Page 6: Prepare The Hood

    4. PREPARE THE HOOD Remove both filters from hood. Disassemble the adaptor/damper (A) from the hood. NOTE: The adapter/damper is located inside the hood. Remove the bottom panel (B) to access the adapter/damper. Refer to figure beside. HO0093 Punch out the electrical and discharge knock-outs for the chosen opening (vertical on top or horizontal at the back of the hood).

  • Page 7: I Nstall The A Dapter /D Amper

    5. INSTALL THE ADAPTER/DAMPER (CONT’D) ERTICAL DISCHARGE For a vertical discharge installation only, leave the foldable flange (C) of the adapter/damper as is. This flange must be located towards the front of the hood. See beside. HO0096 LL INSTALLATIONS Using two 1/2” screws, secure the adapter/damper to the top or back of the hood.

  • Page 8: Connect Wiring

    7. CONNECT WIRING WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally. Connect cable to range hood wiring using included wire connectors.

  • Page 9: Fluorescent Lamps

    9. FLUORESCENT LAMPS WARNING This product contains fluorescent lamps containing mercury. Dispose of appropriately, according to local laws and requirements. This range hood must use compact fluorescent lamps (120 V, 13 W, PLC13, 2700 K with G24q-1 base) (included). WARNING In order to prevent the risk of personal injury, the fluorescent tubes must be cooled down before removing them.

  • Page 10: Cleaning

    10. CLEANING (CONT’D) To remove the blower wheel, first take off its intake ring. Then remove the blower wheel by pulling it down smoothly. HD0156 NOTE: Do not try to remove the black part (C) attached to the bottompanel. When reinstalling the blower wheel, make sure the small tab (D) will fit into one hole of the motor. TAINLESS STEEL CLEANING Don’t: •...

  • Page 11: Operation

    11. OPERATION Always turn on the hood before begining cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after turning off the range. ECHANICAL UTTON ONTROL HC0021 A.
  • Page 12 www.zephyronline.com...
  • Page 13 Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instruc- tions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr's Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses.

This manual is also suitable for:

Es1-e30asEs1-30aw

Table of Contents