Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zephyr Slope ESL-M90AS
Summary of Contents for Zephyr Slope ESL-M90AS
- Page 1 JAN06.0101...
- Page 2 E page F page S page APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner.
-
Page 3: Table Of Contents
www.zephyronline.com Important safety Notice ..............4 Electrical & Installation requirements ..........5 Electrical requirements .............. 5 Before installing the hood ............5 List of Materials ................. 6 Parts supplied: ................6 Parts not supplied ..............6 Dimensions and clearances.............. 7 Installation Instructions .............. -
Page 4: Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B. -
Page 5: Electrical & Installation Requirements
www.zephyronline.com ELECTRICAL REQUIREMENTS Important: Observe all governing codes and ordinances. It is the customer’s responsibility: • To contact a qualified electrical installer. • To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 —... -
Page 6: List Of Materials
PARTS SUPPLIED: • Blower unit housing • Hood canopy • Metal filter x 1 • Halogen light bulb x 2 • Duct covers • Remote Control • Duct Cover support bracket (3 pieces to assemble) • Hardware Packet: 4x8 screws x 4 (to assemble Duct cover support bracket) 6x70 screws x 2 (to fix Duct Cover support bracket) 10x60 wall anchors x 2 (Duct Cover support bracket) 5 x 45 screws x 3 (2 to fix Lower support bracket + 1 for securing hood) -
Page 7: Dimensions And Clearances
www.zephyronline.com 11" 5/8 max 45" 11/16 min 32" 13/16 max 51" 15/16 * min 36" * 6" 5/8 19" 5/8 16" 5/16 ceiling 2"min 1/2" 8" 7/16* 11" 11" 12" 13/16 Ducting and conduit 11" 1/2 area passage(Duct bends are not considered) 21"... -
Page 8: Installation Instructions
Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. VENTING METHODS The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version). Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless (recirculating) version. -
Page 9: Installation - Ductwork Calculation Sheet
www.zephyronline.com Duct pieces Equivalent number Duct pieces Equivalent number lenght x used Total lenght x used Total 3 1/4 ” x 10” 1 Ft. 6" Round 30 Ft. x ( Rect., wall cap straight with damper 6 ” Round,, 1 Ft. 6”... -
Page 10: Installation
4. Tape template, matching center-line and hood Assembling the duct cover support bracket (3 bottom as shown in Figure below. parts): The three parts should be fixed with 4 screws, the 5. Place the lower support bracket on the template support extension is adjustable and should correspond making it coincide with the traced triangle, mark to the internal width of the upper duct cover. - Page 11 www.zephyronline.com 10. Determine the required height for the conduit and 14. If supplied dismounted for shipping, assemble cut a 1-1/4" (3.2 cm) hole at this location. the lower part of the hood with the integral Run wires through hole according the National ventilator housing: Electrical Code or CSA Standards and local codes a.
- Page 12 17. Secure hood with 1 screw on bottom. d. Fasten the hood to the motor unit using 6 screws from the bottom (release the grease filter to access fixing points. Duct cover support bracket Lower support bracket 15. Hang hood with the 2 mounting hooks. Hooks WARNING Excessive Weight Hazard - Use two or more people...
-
Page 13: 19. Electrical Connection
www.zephyronline.com 19. Electrical connection Conduit WARNING Electrical Shock Hazard Warning: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. J-Box cover ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. - Page 14 22. Install duct cover with 2 screws first on duct cover support bracket, then slide the duct lower section towards the bottom. Duct cover 23. Fit control ball with its molex plug on its housing and support bracket twist in place. VIEW Upper duct cover...
-
Page 15: Description Of The Hood
www.zephyronline.com 1 Control panel 2 Grease filter 3 Grease filter release handle 4 Halogen lamp (position and nr. of lamps may vary) 5 Hood canopy 6 Duct cover 7 Air outlet (used for Ductless version only) -
Page 16: Control Ball
CONTROLS Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking. -
Page 17: Remote Control
www.zephyronline.com USING THE REMOTE CONTROL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The remote control may operate in humid environments, but not when placed on wet surfaces. -
Page 18: Maintenance
Prior to any maintenance operation ensure that the cooker hood is disconnected from the power supply. CLEANING The cooker hood should be cleaned regularly internally and externally. For cleaning use a cloth moistened with a neutral liquid detergents. Avoid abrasive detergents. Warning: Failure to carry out the basic standards of the cleaning of the cooker hood and replacement of the filters may cause fire risks. -
Page 19: Trouble Shooting
www.zephyronline.com Issue Cause What to do After installation, the 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit doesn’t work? unit’s power is ON. 2. The power line and the cable locking 2. -
Page 20: Warranty
When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr’s Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses. Services outside of service area and the labor cost incurred in connection with the removal, shipping and reinstallation cost, nor does it cover any other contingent expenses. -
Page 21: List Of Parts And Accessories
www.zephyronline.com Part Description Part# Z0B-0009 halogen bulb, 12V 20 W metal filter GF02IA 2009C remote control (RF) remote control battery ..394 of 1.5V. (4 needed) Part Description Part# ZRC-00SA Ductless Recirculating Kit charcoal replacement filter Z0F-C060 Z1C-00SL duct cover extension kit internal blower - 600 cfm EBI-600A in-line blower - 1100 cfm... - Page 23 www.zephyronline.com...
Need help?
Do you have a question about the Slope ESL-M90AS and is the answer not in the manual?
Questions and answers