Zephyr Twister AK8000AS Use, Care And Installation Manual
Zephyr ak8000as ventilation hood user manual
Hide thumbs
Also See for Twister AK8000AS:
- Use, care and installation manual (44 pages) ,
- Use, care and installation manual (7 pages)
Related Manuals for Zephyr Twister AK8000AS
Summary of Contents for Zephyr Twister AK8000AS
- Page 1 Twister AK8000AS Tornado I AK8100AS Model number: Serial Number: Date of Purchase: Sales Dealer: JAN08.0201 © 2008 Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Specifi cations Electrical Installing the Power Pack FEATURES & CONTROLS Slide Controls MAINTENANCE Cleaning and Installing Filters AK8000AS Recirculating Kit Lights TROUBLESHOOTING LIST OF PARTS AND ACCESSORIES...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product. AK8000AS (290 cfm) - 150W, 1.25 Amps AK8100AS (600 cfm) - 390W, 3.25 Amps A cable locking connector (not supplied) might also be required by local codes. -
Page 6: Hardware Package Contents
MODELS: AK8000AS AND AK8100AS PARTS SUPPLIED AK8000AS and AK8100AS 1 - Power Pack 1 - Metal mesh fi lter (AK8000AS), 1 - Decorative mesh fi lter (AK8100AS) 2 - Halogen light bulbs (pre-installed) 1 - Single internal blower (pre-installed) 1 - Hardware package... - Page 7 Equivalent number Duct pieces length x used 3-1/ 4” x 10” 1 Ft. Rect., straight 6” Round, 1 Ft. straight 1 Ft. 7”-10” Round, straight 3-1/ 4” x 10” 15 Ft. Rect.90 elbow 3-1/ 4” x 10” 9 Ft. Rect.45 elbow 3-1/ 4”...
- Page 8 Min 26" - Max 36" 36" DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency . Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Also use calculation (on page 5) to compute total available duct run when using elbows, transitions and caps.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options side wall cap w/ gravity damper...
- Page 10 10-5/8” 5-7/8” 11-13/16” 26-9/16” 27-9/16” front 27-9/16” 25-3/4” 15” 1-5/16” 18-15/16” bottom www.zephyronline.com 4-1/8” 10-5/16” side...
- Page 11 ELECTRICAL WARNING All Electrical work must be performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Install optional AK08xxAS Stainless Steel Liner. Review manual included with liner for more details. 2. If no liner is used cut out an opening in the bottom of the cabinet by following the dimensions in FIG 1.
- Page 13 Blower On/Off Speed Selection I I I BLOWER ON/OFF/SPEED SELECTION 0 is off, I is low speed, II is medium speed and III is high speed. LIGHTS BRIGHT/DIM/OFF 0 is off, I is dim, and II is bright. Lights Bright/Dim/Off...
-
Page 14: Surface Maintenance
2. Push fi lter handle in towards left side of Power Pack. 3. Pivot fi lter up and lock into place. Hood Model: Part No. Qty. to Order AK8000AS 50200022 Installing Decorative Mesh Filter, FIG 6: Hood Model: Part No. - Page 15 fi lter and a return air vent is needed to direct air back into the kitchen. The standard metal mesh fi lter is intended to capture residue from cooking and the optional charcoal fi lter helps to purify fumes exhausted from cooking in recirculating mode. Purchase recirculating kit as follows, for AK8000AS ONLY: Hood Model: Part No.
-
Page 16: Replacing Light Bulbs
Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 15 of the manual. Bottom View... - Page 17 TROUBLESHOOTING PROCEDURES FOR TWISTER AND TORNADO 1 Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 18 Light Bulb MR16 (GU10) 35W (each) Metal Mesh Filter (each) Decorative Mesh Filter (each) Optional Accessories Liner,30” Liner,36” Recirculating Kit (AK8000AS ONLY) To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 www.zephyronline.com PART # Z0B-0023 50200022...
-
Page 19: Limited Warranty
Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows: Ten Year Limited Warranty for Parts: For ten years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.