Emerson Liebert GXT3 User Manual page 22

Display parameter
pS pASSWORD
/ pROBe pARAMeTeRS
/C ambient probe calibration (x 0.1°C/°F)
/ Measurement stability
/4 probe display: 0 = regulation probe, 1 = product food probe (second probe)
/5 °C/°F (0=°C, 1=°F)
r ReGULATOR pARAMeTeRS
rd Regulating differential (hysteresis 0=0.5 °C/ °F)
r1 Minimum allowable set
r Maximum allowable set Cr1 17 °C/°F 60
r3 Enabling Ed alarm: max duration of defrost is reached (0 = no, 1 = yes)
r4 Automatic variation of the Set-Point with closed curtain-switch (A4=4)
c COMpReSSOR pARAMeTeRS
c0 Delay in the compressor start-up after switch-on
c1 Minimum time between two following compressor start-ups
c Compressor shutdown minimum time
c3 Compressor operation minimum time
c4 Safety compressor (0 = OFF, 100 = ON)
cc Continuous cycle duration
c6 Alarm delay after continuous cycle
d DeFROST pARAMeTeRS
d0 defrost type (0 = heater, 1 = hot gas,  = time resistance, 3 = time hot gas)
d1 Time interval between two defrost cycles
dt End defrost temperature
dP Max defrost duration or effective duration if d0= or 3
d4 Defrost after start-up (0 = no, 1 = yes)
d5 Delay defrost after control Switch-On or from digital input (A4 or A5=4)
d6 Block temperature display during defrost (0 = no, 1 = yes)
dd Dripping time after defrost
d8 Alarm delay after defrost
d9 defrost priority over compressor protection (0 = no, 1 = yes)
d/ Temperature defrost probe display
dC Time base (0=hours/min, 1=min/s) Only for dl and dP
A ALARM pARAMeTeRS
A0 Alarms and fans differential (0=0.5 °C/°F)
AL Low temperature alarm (max. variation as to the Set-Point). AL=0 excluded Low temperature alarm
AH High temperature alarm (max. variation as to the Set-Point). AH=0 excluded High temperature alarm
Ad Temperature alarm delay
A7 Measurement delay time for the input "delayed alarm" (A4 or A5=)
F FAn pARAMeTeRS
F0 Management of fans: 0=fans ON, specific phases excluded (F2, F3 and Fd) 1 = fans ON (dependent
on parameter F1) specific phases excluded
F1 Fan power on temperature
F Fans OFF when the compressor is OFF (0 = no, 1 = yes)
F3 Fans OFF during defrost (0 = no, 1 = yes)
Fd Stop after dripping ON for each F0 value
H OTHeR SeLeCTIOnS
H0 Serial address
H1 Selection of the alarm relay operation 0=alarm ON, energized relay, 1= alarm ON, disenergized relay
H 0=disabled buttons, 1=enabled buttons
H5 Identification code for programming key (programmed by supervisor)
T External parameter programming
*show the set value
NU*: not used parameter, leave the default value
Sporland Omnistat Time Clock program Settings (Cont'd)
please contact Sporlan valve Company for further information. www.sporIan.com
LIST OF pARAMeTeRS

IGIC-CIDM-0909
Type Min Max Unit Default
F 0 199 - 
F -17 17 °C/°F 0.0
C 1 15 - 4
C 0 1 flag 0
C 0 1 flag 0
F 0 19 °C/°F 
C -50 r °C/°F -50
C r1 17 °C/°F 60
C 0 1 flag 0
C -0 0 °C/°F 3
C 0 15 min 0
C 0 15 min 0
C 0 15 min 0
C 0 15 min 0
C 0 100 min 0
C 0 15 hours 4
C 0 15 hours 
C 0 3 flag 0
F 0 199 hours 8
F -50 17 °C/°F 4
F 1 199 min 30
C 0 1 flag 0
C 0 199 min 0
C 0 1 flag 1
F 0 15 min 
F 0 15 hours 1
C 0 1 flag 0
F - - °C/°F -
C 0 1 flag 0
C 0 19 °C/°F 0
F 0 17 °C/°F 0
F 0 17 °C/°F 0
C 0 199 min 0
C 0 199 min 0
C 0 1 flag 0
F -50 17 °C/°F 5
C 0 1 flag 1
C 0 1 flag 1
F 0 15 min 1
C 0 199 - 1
C 0 1 flag 1
C 0 1 flag 1
F -99 199 - -
C -99 99 - 0
value
CIDM
22
0.0
4
1
1
8
26°F
32°F
0
nU*
1
1
1
2
10
2
6
2
4
60
25
0
0
1
0
2
0
-
0
0
0
0
0
nU*
n/A
n/A
n/A
n/A
n/A
1
1
0
-
0