This UPS is not intended for use with life support and other designated critical devices. Maximum load must not exceed that shown on the UPS rating label. This UPS is designed for data processing equipment. If uncertain, consult your local dealer or Emerson Network Power representative.
Page 8
The Liebert GXT4 series complies with the requirements of EMC Directive 2004/108/EC and the published technical standards. Continued compliance requires installation in accordance with these instructions and use of accessories approved by Emerson ® Information for the Protection of the Environment UPS SERVICING—This UPS makes use of components dangerous for the environment (electronic...
LOSSARY YMBOLS Risk of electrical shock Indicates caution followed by important instructions AC input AC output Requests the user to consult the manual Indicates the unit contains a valve-regulated lead acid battery PbH2SO4 Recycle DC voltage Equipment grounding conductor Bonded to ground AC voltage WEEE ®...
• Output voltage selection function Available Models Available models of the UPS are listed in Table 1: Table 1 UPS models, power ratings Nominal Power Rating Model Number GXT4-5000RT230 5000VA / 4000W GXT4-5000RT230E GXT4-6000RT230 6000VA / 4800W GXT4-6000RT230E GXT4-10000RT230 10000VA / 9000W GXT4-10000RT230E ®...
Product Description Appearance and Components 1.3.1 Appearance The Liebert GXT4 rack/tower models in various power ratings have the same general appearance, controls and features (see Figure 1). The various rack/tower models differ largely in the type of receptacles each has. Figure 1 Liebert GXT4 5000VA and 6000VA, front view Upper Bezel...
Product Description 1.3.2 Rear Panel Features The rear panel of the Liebert GXT4 has these features: • Liebert IntelliSlot ® Port • Cooling Fan • USB port • Terminal Block Communication • Input Circuit Breaker • Output Circuit Breakers • General Output Receptacles •...
Product Description Internal Battery Packs The UPS has two internal battery packs behind a battery access door on the front of the unit. Each internal battery pack is fitted with a connector to link to the UPS. Figure 4 Internal battery pack with connector Battery Handle Battery Connector GXT4 10,000 Battery...
Product Description Major Components General Dynamic Outlet POD Bypass Dependent Rectifier/ TVSS EMI/RFI Inverter General EMI/RFI Output DC-DC Outlet POD Input Filter Converter Dependent Filter Battery General Charger Outlet POD Dependent General Outlet POD Dependent Battery The UPS is composed of mains input, TVSS and EMI/RFI filters, rectifier/PFC, inverter, battery charger, DC-to-DC converter, battery, dynamic bypass and UPS output.
Product Description 1.6.6 Battery The Liebert GXT4 utilizes valve-regulated, nonspillable, lead acid batteries. To maintain battery design life, operate the UPS in an ambient temperature of 15°C to 25°C (59°F to 77°F). Optional external battery cabinets are available to extend battery run times. For run times, see Table 16. 1.6.7 Internal Bypass The Liebert GXT4 provides an alternate path for mains power to the connected load in the unlikely...
Product Description 1.7.3 Battery Mode The Liebert GXT4 enters Battery Mode when mains power fails or is outside acceptable limits. The battery system supplies power through the DC-to-DC converter to the inverter to generate clean AC power for the connected loads. When the Liebert GXT4 enters Battery Mode, the UPS sounds a half-second beep at 10-second intervals.
® representative immediately. • Check the accessories against the delivery list. If there is any discrepancy, contact your local dealer or your Emerson representative immediately CAUTION The UPS is heavy (see 8.0 - Specifications). Take proper precautions when lifting or moving it.
Installation Install the Main Cabinet The Liebert GXT4 may be installed in either a tower configuration or in a rack, depending on available space and use considerations. Determine the type of installation and follow the appropriate instructions in either 2.4.1 - Tower UPS Installation or 2.4.2 - Rack Installation. 2.4.1 Tower UPS Installation To install the Liebert GXT4 as a tower:...
3. Securing hardware and slide rails are sold separately. Please contact your local dealer or Emerson representative for these additional options and any assistance needed. Fasten the slides into position with the screws per the instructions included with the slide rails.
Installation NOTE When removing the External Battery Cabinet, the circuit breaker on the rear of the cabinet must be turned Off before disconnecting the cable. NOTE If the UPS is to be shipped or stored for an extended time, the connector should be disconnected.
UPS-PFC, Battery Inverter Terminal Block Connections—PD2-CE6HDWRMBS and PD2-CE10HDWRMBS Conduit entry holes are provided on the rear and side of the box. Input and output wiring should not share the same conduit. Emerson ® recommends using strain relief when installing the wire.
Installation IT Power System Configuration 1. Remove screws on the IT Power System Access Cover as shown in Figure 14. 2. Disconnect the connectors as shown in figure. 3. Install IT Power System Access Cover and screws. Figure 14 Remove cover from IT Power System Connectors compartment IT Power System Remove Screws Connectors...
Operation and Display Panel PERATION AND ISPLAY ANEL This chapter describes the Liebert GXT4 controls, particularly the operation and display panel on the front of the Liebert GXT4. The panel has four control buttons, seven LED indicators and a liquid crystal display (LCD), as shown in Figure 15.
Operation and Display Panel Control Buttons The four control buttons on the front of the operation and display panel are: • ESC • Up • Down • Enter Figure 15 shows the buttons’ locations; their descriptions and functions are shown in Table 5. Table 5 Control buttons Control Buttons...
Operation and Display Panel Figure 16 Menu structure Audible Alarm Output Startup on Bypass Load Enable Auto Shutdown Status Input Enable Auto Restart Battery Start Windows Frequency Selection Time Since Startup Output Level Selection System Status Configuration Parallel Selection Turn UPS On Turn UPS Turn UPS Off Battery Cabinets...
When the Liebert GXT4 is starting up, it initiates a self-test and displays the screen shown in Figure 17 for about 10 seconds. Figure 17 Startup screen EMERSON Network Power After about 10 seconds, the LCD shows one of the On screens in Figure 18; the screen shown depends on whether input power is available.
Operation and Display Panel 3.4.2 Default Screen Press any button in the START SUCCESSFUL screen to enter the default interface, shown in Figure 20. Figure 20 Default screen Values shown will vary GXT4-UPS 3KVA according to installation and configuration. O/P: 230V 50HZ 11.7A I /P: 230V 50HZ 13.1A BATT: 100 % 3MINS LOAD: 100%...
Operation and Display Panel Figure 22 Status screens OUTPUT LOAD INPUT VOLT 120V VOLTAGE 120V FREQ 60 HZ WATT : 1620W FREQUENCY : 60HZ CURR 18.6A 1800VA CURRENT 17.6A POWER : 97KWH POWER : 2112 KWH BATTERY TIME SINCE STARTUP CAPACITY : RUNTIME : 100 MINS...
Operation and Display Panel UPS Screen Select MAIN MENU > CONFIGURATION > UPS to enter the UPS screen. This menu has six screens, as shown in Figure 24. Figure 24 UPS screens AUDIBLE ALARM STARTUP ON BYPASS GUARANTEE SHUTDOWN ENABLE AUTO RESTART FREQUENCY SELECTION VOLTAGE SELECTION AUTO - BYPASS ENABLE...
Operation and Display Panel Battery Screen Select MAIN MENU > CONFIGURATION > BATTERY to enter the BATTERY screen. This menu has four screens, as shown in Figure 26. Figure 26 Battery screen EXT BATT CABINET LOW BATTERY TIME CABINETS MINS BATT TEST INTERVAL BATT REPLACE TIME WEEKS...
Configuration Program user manual on the included CD. Figure 29 Language screen 1 English Select 2 COLOR and press the Enter button to enter the COLOR screen, as shown in Figure 30. Figure 30 Color screen EMERSON EMERSON EMERSON EMERSON ® ™...
Operation and Display Panel FACTORY DEFAULT Screen Select MAIN MENU -> 2 CONFIGURATION -> 7 FACTORY DEFAULT to enter the FACTORY DEFAULT screen, as shown in Figure 31. Figure 31 Factory Default screen RESET ALL SETTINGS TO FACTORY DEFAULT SETTINGS? Control Screen Select MAIN MENU ->...
Operation and Display Panel ALARM CONTROL Screen Select MAIN MENU -> 3 CONTROL -> 2 ALARM CONTROL to enter the ALARM CONTROL screen, as shown in Figure 34. This section allows active audible alarms to be silenced. To completely turn off the audible alarm, refer to CONFIGURATION >...
Operation and Display Panel CLEAR LOG Screen Select MAIN MENU > LOG > CLEAR LOG to enter the CLEAR LOG screen, as shown in Figure 37. Figure 37 Clear Log screen DO YOU WANT TO CLEAR EVENT LOGS? Press the Up or Down button to move the cursor to the required item. Press the Enter button to confirm the settings.
Operation and Display Panel Figure 39 Network screens ADDRESS MAC ADDRESS IPV4 ADDRESS IPV6 STATIC 00-02-11-4X-AX 10.163.226 .231 /24 ADDRESS IPV6 LINK ADDRESS IPV6 AUTO Fe80::202:99ff:fe0f:4ba 3.4.4 Prompt List A prompt screen is displayed during the operation of the system to alert to certain conditions and/or to require confirmation of a command or other operation.
Operation and Display Panel 3.4.5 Warning List All UPS warning messages are described in Table 7. Table 7 Warning list Warning Description The utility power is not available, or it cannot satisfy the requirements Utility power not available for the UPS to operate UPS batteries low and exhausted soon The battery capacity is low and will be exhausted soon.
• After the batteries have been retested, if the battery test still shows FAILED, contact your local Emerson ® representative or Emerson Network Power Channel Support. Manual Bypass To manually transfer the connected equipment to the internal bypass: 1. From the main menu select Control then press enter.
Operation Disconnecting Input Power from the Liebert GXT4 1. After the UPS has been shut down as detailed in 4.5 - Shut Down the Liebert GXT4, disconnect the input cable from the wall socket. 2. Wait 30 seconds and verify that all indicators have turned Off and the fan has stopped; this indicates that the power-Off is complete.
The Liebert IntelliSlot UNITY card also enables monitoring external temperature, humidity and contact closure inputs using external sensors. (The Liebert IS-UNITY-DP compatibility will be a future release, contact your Emerson sales representative for availability.) Follow instructions provided with the Liebert IntelliSlot card to configure Liebert MultiLink , the ®...
• Set the Auto-Battery test to 8, 12, 16, 20, or 26 weeks (default is 8 weeks) • Select the number of external battery cabinets connected to the UPS to adjust the remaining run time calculated by Emerson software products (default is zero) ®...
Communication Terminal Block Communication The Terminal Block includes eight pins, as shown in Figure 40. Figure 40 Terminal Block Communication pin layout Any Mode Shutdown Battery Mode Shutdown On Battery Mode Low Battery 5.3.1 Any Mode Shutdown The purpose of Any Mode Shutdown is to shut down the UPS output by turning Off the rectifier, inverter and static switch so that there is no power to the loads.
Communication 5.3.2 Battery Mode Shutdown Battery Mode Shutdown permits shutting down the UPS by turning Off the rectifier, inverter and static switch so that there is no power to the load when the UPS is On Battery. The auxiliary power for the UPS will still be active.
Communication Remote Emergency Power Off The UPS is equipped with a Remote Emergency Power Off (REPO) connector. The user must supply a means of interfacing with the REPO circuit to allow disconnecting the UPS input feeder breaker to remove all sources of power to the UPS and connected equipment to comply with national and local wiring codes and regulations.
UPS functions. Replacing the Internal Battery Pack The Liebert GXT4 is designed to allow the user to replace the internal battery pack safely. Read the safety cautions before proceeding. Contact your local dealer or Emerson representative to obtain the ®...
The Liebert GXT4 charges the batteries continuously when it is connected to the mains input power. If the Liebert GXT4 will be stored for a long time, Emerson recommends connecting the UPS to input power for at least 24 hours every four to six months to ensure full recharge of the batteries.
• Check whether the UPS is faulty: Is the Fault Indicator On? Is the UPS sounding an alarm? • Check whether the UPS is operating in Bypass Mode. Normally, the UPS operates in Normal Mode. If it is operating in Bypass Mode, stop and contact your local Emerson representative, or Emerson Channel Support.
Troubleshooting ROUBLESHOOTING This section indicates various UPS symptoms a user may encounter and provides a troubleshooting guide in the event the UPS develops a problem. Use the following information to determine whether external factors caused the problem and how to remedy the situation. UPS Symptoms The following symptoms indicate the Liebert GXT4 is malfunctioning: •...
Specifications PECIFICATIONS Table 13 UPS specifications GXT4-5000RT230 GXT4-6000RT230 GXT4-10000RT230 Model # GXT4-5000RT230E GXT4-6000RT230E GXT4-10000RT230E Rating 5000VA/4000W 6000VA/4800W 10,000VA/9000W Dimensions, mm (in) 430 x 574 x 217 430 x 581 x 261 Unit, W x D x H (16.9 x 22.4 x 8.5) (16.9 x 22.9 x 10.3)
Specifications Table 13 UPS specifications (continued) GXT4-5000RT230 GXT4-6000RT230 GXT4-10000RT230 Model # GXT4-5000RT230E GXT4-6000RT230E GXT4-10000RT230E Bypass Protection Limits Disable Bypass Operation If input voltage exceeds ±15% of the nominal voltage Re-Enable Bypass Operation If input voltage returns to within ±10% of nominal output voltage...
Specifications Table 15 External battery cabinet specifications GXT4-240VBATT Model Number GXT4-5000RT230; GXT4-6000RT230; GXT4-10000RT230 Used with UPS Model Dimensions, W x D x H, mm (in.) Unit (with bezel) 430 x 581 x 173 (16.9 x 22.9 x 6.8) 530 x 745 x 475 (20.9 x 29.3 x 18.7)
• To contact warranty support by e-mail: dpg.warranty@emerson.com Technical Support Technical support contacts are listed on the back cover of this document. To contact Emerson Channel Product Support: Phone • NORTH AMERICA: 1-800-222-5877 • OUTSIDE NORTH AMERICA: 00-800-1155-4499 E-mail •...
Page 56
Philippines ® Liebert is a registered trademark of Liebert Corporation. +63 2 687 6615 All names referred to are trademarks Fax: +63 2 730 9572 or registered trademarks of their respective owners. SLI-23197_REV0_10-14 Emerson Network Power Liebert www.emerson.com...