Download Print this page
CyberData VoIP V2 Specifications

CyberData VoIP V2 Specifications

Voip v2 loudspeaker amplifier
Hide thumbs Also See for VoIP V2:

Advertisement

Now with up to 25 watts output (802.3at)
VoIP V2 Loudspeaker Amplifier
The new CyberData V2 SIP-enabled VoIP Loudspeaker
Amplifier provides an easy method for implementing an IP-based
overhead paging system for both new and legacy installations.
With up to 25 watts of driving power (802.3at), the Amplifier
provides direct drive of a standard Horn speaker and supports
a line-out connector for connection to an external amplifier.
The interface is compatible with most SIP-based IP PBX
servers that comply with the SIP RFC 3261. For non-SIP
environments, the Loudspeaker Amplifier can be configured to
listen to multicast address and port number combinations to
form paging zones.
Ringer Mode
The VoIP V2 Loudspeaker Amplifier supports two SIP
extensions. One extension can be assigned to a page group for
auto answer paging. The second extension can be assigned to
a "First-to-Answer" ring group with IP phones. An audio ring file
is activated when the second SIP extension of the ceiling
speaker is dialed. If any of the IP phones in the ring group is
answered (or if the caller hangs up), the Loudspeaker Amplifier
stops ringing.
Features
SIP and Simultaneous Multicast
Dual-speed ethernet 10/100 Mbps
Web-based configuration
PoE 802.3at and 802.3af-enabled
Line-in for background music
Line-out connector
DTMF controlled relay
Direct 8 Ohm speaker drive
User-uploadable tones and messages
Digital and manual volume control
Second SIP endpoint "Night Ringer"
Autoprovisioning
Auto-call voice message from input port sense
The IP Endpoint Company
CyberData Corporation
3 Justin Court, Monterey, CA 93940
The IP Endpoint Company
Loudspeaker (part #011068) must be purchased separately.
Specifications
Ethernet I/F
Power Input
Operating Temperature
Protocol
Payload Types
Regulatory Compliance
Warranty
Dimensions
Output
Line In:
Input Signal Amplitudes
Input Impedance
Line Out:
Output Signal Amplitudes
Output Level
Total Harmonic Distortion
Output Impedance
Boxed Weight
Part Number
Loudspeaker Amplifier, AC
Loudspeaker Amplifier, Wireless
Loudspeaker Amplifier, PoE
Loudspeaker Part Number
831.373.2601
Fax: 831.373.4193
10/100 Mbps
PoE 802.3at or 802.3af
-30 to 55 C (-22 to 131 F)
SIP RFC 3261
G711
FCC Class A
2 Years Limited
14" x 10" x 4"
802.3af - up to 8 watts
802.3at - up to 25 watts
2.0 VPP maximum
10k Ohm
2.0 VPP maximum
+2dBm nominal
0.5% maximum
10k Ohm
6.5 lbs.
011095
011096
011097
011068
www.cyberdata.net

Advertisement

loading
Need help?

Need help?

Do you have a question about the VoIP V2 and is the answer not in the manual?

Questions and answers

Summary of Contents for CyberData VoIP V2

  • Page 1 PoE 802.3at or 802.3af Ringer Mode Operating Temperature -30 to 55 C (-22 to 131 F) The VoIP V2 Loudspeaker Amplifier supports two SIP Protocol SIP RFC 3261 extensions. One extension can be assigned to a page group for Payload Types G711 auto answer paging.
  • Page 2 *For AC wiring, use a qualified electrician. Typical Installation - PoE 802.3af (Part# 011097) 802.3af Generic PoE Switch or 802.3at High Power Switch 011097 VoIP V2 Loudspeaker Amplifiers – No AC Required IP Phone IP-PBX Server 930340G/110706 CyberData Corporation 3 Justin Court, Monterey, CA 93940 831.373.2601...
  • Page 3 VoIP V2 Loudspeaker Amplifier Configuring the V2 Loudspeaker Amplifier for Alarm Sensing User can upload an audio message to the Loudspeaker Amplifier. When the “Sense-In” is activated, the stored IP Phone Audio file will play out the local speaker and repeat until the condition is cleared.