Setting Up An Intelliflo Vs 3050 And Vsf+Svrs Pump From Equipment Screen - Pentair INTELLITOUCH User Manual

66
IntelliFlo VS 3050 and VSF+SVRS Pump Setup
Setting up IntelliFlo VS 3050 and VSF +SVRS pump from the Equipment Screen
After you have assigned the pump address on the IntelliFlo VS 3050 and VSF +SVRS pump (see
previous page), assign the pump type being used and the pump address in the IntelliTouch "Equipment"
screen. When using a single IntelliFlo VS 3050 or VSF +SVRS pump for remote control with
IntelliTouch, the default address is always pump #1. When using multiple IntelliFlo VS 3050 and VSF
+SVRS pumps with IntelliTouch assign an address to each pump. For IntelliFlo VS 3050 set the address
to #1, #2, #3 or #4. For IntelliFlo VSF +SVRS set the address from #1-#8. The address set at the pump
must match the IntelliFlo pump number selected in the "Equipment" screen. This is also where you
select the pump type being used and its address (IntelliFlo VF 3050 #1, IntelliFlo VS 3050 #2, IntelliFlo
VSF +SVRS #3 etc.).
Getting There
MENU SETUP EQUIPMENT INTELLIFLO
To select the pump type (IntelliFlo VS 3050 and IntelliFlo VSF +SVRS) and it's address:
1. Press one of the left side buttons next to the IntelliFlo pump type and number (address) that you
wish to change. Note: IntelliFlo VS 3050 pumps can be assigned to address #1 through #4.
IntelliFlo VSF +SVRS 3050 pumps can be assigned to address #1 through #16.
Left side
button
2. Press the left side button again next to the IntelliFlo pump selected in step 1. The next screen message
indicates that you can change the pump type displayed or no change to the selected pump type.
Pressing the lower "NO" button returns you to the previous screen. Pressing the same selected pump
type again from this screen displays the next pump type. This way can scroll through the three pump
types available. The three pump types to choose from are; IFLO VS3050, IFLO VF 3050 and IFLO
VSF +SVRS.
3. Press the lower right "YES" button to accept the pump type selection or press the "NO" button for no
change. On the next screen, press the Save button to save the setting. The main Equipment screen is
displayed. Press the button next to
assigned to pump #1. To set another IntelliFlo 4 pump, repeat steps 1-3.
THIS WILL CHANGE THE PUMP
IFLO VF 3050
FROM AN
IFLO VS 3050 ?
AN
THIS WILL ERASE ALL OF
THIS PUMPS DATA !
NO
NO YES buttons
IntelliTouch Control System User's Guide
®
IFLO VF 3050 #1 POOL
IFLO VS 3050 #2 SPA
IFLO VSF+SVRS #3
IFLO VS 3050 #4 AUX 3
NEXT GROUP OF PUMPS
MENU/SETP/EQUIP/IFLO/SELECT
BACK EXIT
INTELLIFLO
IntelliFlo
TO
VF 3050
assigned as
pump #1
YES
(Continued)
Press this
button to
change to
IntelliFlo
pump type
. The main pump screen displays IntelliFlo pump type
PENTAIR IFLO VF 3050
IFLO VF 3050 #1 POOL
SET PARAMETERS
ASSIGN CUSTOM FLOWS
INTELLIFLO STATUS
MENU/SETP/EQUIP/INTELLIFLO
BACK SAVE EXIT
Save button
PENTAIR IFLO VF 3050
IFLO VF 3050 #1 POOL
SET PARAMETERS
ASSIGN CUSTOM FLOWS
INTELLIFLO STATUS
MENU/SETP/EQUIP/INTELLIFLO
BACK SAVE PREV EXIT
IFLO VF 3050 #1 POOL
IFLO VS 3050 #2 SPA
IFLO VSF+SVRS #3
IFLO VS 3050 #4 AUX 3
NEXT GROUP OF PUMPS
MENU/SETP/EQUIP/IFLO/SELECT
BACK EXIT