1:10 distribution amplifier for hdmi 1.3 (26 pages)
Summary of Contents for Gefen EXT-DVI-2-HDSDIPRO
Page 1
® DVI to HD-SDI Pro Scaler EXT-DVI-2-HDSDIPRO www.gefen.com...
Page 2
Notice Gefen, LLC reserves the right to make changes in the hard ware, packaging, and any accompanying doc u men ta tion without prior written notice. The DVI to HDSDI PRO is a trademark of Gefen LLC All trademarks are the property of their respective owners.
INTRODUCTION The Gefen DVI to HDSDI Pro Scaler combines two of our DVI to HDSDI Scaler Plus units into one rack-mountable unit. It still incorporates full single-link DVI-D conversion scaled to your choice of SD/HDSDI Single- or Dual-link modes, but now simplifi...
OPERATION NOTES On power up, the DVI to HD-SDI Pro will automatically detect the format of the input signal. The unit is controlled using the included remote or through the RS-232 port. The following are the buttons for the RMT-8HDS-IR Remote Control Unit (included): - UP (Navigates cursor up) - LEFT (Navigates cursor left) - Enter (Accept Operation / Return to Menu)
PANEL DESCRIPTIONS Front IR Receiver 1 IR Receiver 2 Power LED Indicator RS-232 RS-232 Port 1 Port 2 Back HD-SDI HD-SDI Output 1 Output 1 Power Input HD-SDI HD-SDI GenLock GenLock Input 1 Output 2 Input 2 Output 2 Reference Reference Input 1 Input 2...
Menu Functions Aspect: -Full Screen: Stretches input to fi ll the Monitor. -Letter / Pillar Box: Sets the aspect ratio to fi t a letter or pillar box format. -Panoramic: Panoramic Zoom feature -Extract: Feature to magnify the signal. -Extract Size: Adjusts signal magnifi cation. -Horizontal / Vertical Position: Moves the magnifi...
Menu Functions (continued...) Input: -Input Video Format: Auto Detect by default. Signal can be forced to a specifi c High-defi nition resolution. (Please see Supported Input/Output Resolutions for more information). -Input Graphic Format: Auto Detect by default. Signal can be forced to a specifi...
RMT-8HDS-IR Installation 1. Remove battery cover from the back of the RMT-8HDS-IR remote. 2. Verify that DIP switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down.
RS-232 CONTROL The DVI to HD-SDI Pro can be controlled via the RS-232 port on the rear of the unit. Please refer to the Communication Protocol for Gennum VXP Products on Gefen’s website at: http://www.gefen.com/kvm/support/download.jsp. FIRMWARE UPDATE PROCEDURE Connect your computer’s RS-232 (serial) port to the RS-232 port on the DVI to HD-SDI Scaler Pro using a male to female, straight pin-to-pin RS-232 cable.
SPECIFICATIONS Input Video Bandwidth................2 x 165 MHz Output Video Bandwidth................4 x 165 MHz Maximum Input Resolution................2048x1080 Maximum Output Resolution..............2048x1080p24 DVI Connector............DVI-I 29 pin female (digital only) SDI/HDSDI Connector................BNC female Data Port....................Serial RS-232 Power Supply....................5V 8A DC Power Consumption................20 watts (Max.) Dimensions..................6.5”W x 1”H x 6.75”H Shipping Weight....................5 lbs.
Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notifi ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi...
Page 14
Rev A3 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com This product uses UL listed power supplies.