Intermec EasyCoder PM4i User Manual
  1. Manuals
  2. Brands
  3. Intermec Manuals
  4. Label Maker
  5. PM4I
  6. User manual

Intermec EasyCoder PM4i User Manual

Bar code label printer (ipl version)
Hide thumbs Also See for EasyCoder PM4i:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Instruction and Installation Manual
User's Guide
EasyCoder PM4i
Bar Code Label
Printer
(IPL Version)

Advertisement

Table of Contents
loading

Related Manuals for Intermec EasyCoder PM4i

Summary of Contents for Intermec EasyCoder PM4i

  • Page 1 User’s Guide EasyCoder PM4i Bar Code Label Printer (IPL Version)
  • Page 2 Service support: +46 31 869500 The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec.

  • Page 3: Table Of Contents

    GS Notice (Germany) ..............vii EU Standard EN 55022 (The European Union) ......vii Declaration of Conformity (CE) ..........viii Introduction Description of EasyCoder PM4i Printer......... 2 Safety Summary ................3 Product Identifi cation ..............3 Installation Unpacking the Printer..............6 Front View..................
  • Page 4 Form Adj Dots Y..........48 Confi guration ..............49 Label Taken Sensor.......... 49 Emulation ............49 Print Speed............49 Cutter ............. 49 Setup Mode Navigating in Setup Mode ............52 Setup Mode Overviews ..............54 Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 5 Label Stop Sensor Position Adjustment ........79 Printhead Pressure................ 80 Ribbon Break Shaft..............81 Technical Specifi cations Technical Data ................84 Media Specifi cations Media Roll Size ................88 Media ..................89 Non-Adhesive Strip ............89 Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 6 RS-232 Interface ................98 Optional Interfaces ..............99 Supported IPL Commands Commands and Syntax List ............102 Intermec Supplies Direct Thermal Media..............108 Thermal Transfer Media............. 109 Transfer Ribbons................ 110 Setting the Media Sensitivity Number........111 Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 7: Fcc Notice (U.s.a.)

    EU Standard EN 55022 (The European Union) WARNING This is a Class A ITE product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 8: Declaration Of Conformity (Ce)

    89/336/EEC and 73/23/EEC Mölndal 2003-03-12 ..............Per-Ove Jacobsson /. Intermec assumes no responsibility regarding the CE Directive if the printer is handled, modifi ed, or installed in other manners than those described in Intermec’s manuals. viii Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 9: Introduction

    Introduction This chapter introduces the EasyCoder PM4i printer. The chapter covers the following topics: • Description of EasyCoder PM4i • Safety summary • Product identifi cation Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 10: Description Of Easycoder Pm4I Printer

    Chapter 1— Introduction Description of EasyCoder PM4i Printer The EasyCoder PM4i is a sturdy thermal transfer printer with a print- head resolution of 8 dots/mm = 203.2 dot/inch and a maximum print width of 104 mm (4.095 inches). It offers a large number of useful features, such as: •...

  • Page 11: Safety Summary

    Chapter 1—Introduction Safety Summary Intermec assumes no responsibility regarding the CE Directive if the printer is handled, modifi ed, or installed in any way other than that described in Intermec’s manuals. • Read this manual carefully before connecting the printer.
  • Page 12 Chapter 1— Introduction Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 13: Installation

    Installation This chapter explains how to unpack and install the EasyCoder PM4i and also describes the printer’s vari- ous parts in detail. It covers the following topics: • Unpacking the printer • Parts on the printer’s front • Parts on the printer’s rear plate •...

  • Page 14: Unpacking The Printer

    230 VAC plug If the printer has been damaged in any way during transportation, com- plain to the carrier immediately. If the delivery is incorrect or any parts are missing, report it immediately to the distributor. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 15: Front View

    The printed labels, tickets, or tags are presented at the front of the print mechanism, which is covered by a door. Control lamps Display window Feed/Pause button Keyboard Side door Print mechanism Front door Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 16: Rear View

    Wireless antenna (option) Memory card slot Provision for IEEE 1284 parallel interface board On/Off Switch (not used) AC Power cord socket RS-232 serial interface (not used) Machine label Intake slot for external media supply Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 17: Media Compartment

    There is also an optional rotating media supply hub. Also see Chapter 9, “Options.” Lock (option) Side door Thermal transfer Inspection mechanism window Media supply roll post with edge guide Keyboard Integral liner takeup Front door Slack absorber Print mechanism Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 18: Media Supply Roll Post

    Setup Mode. There are also a 3-inch adapter and a label roll retainer. Another option is an internal guide for media placed behind the printer (for example fan-folds). For illustrations, see Chapter 8 “Options”. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 19: Print Mechanism

    Ribbon supply hub Ribbon break shaft Thermal printhead Pressure arm Finisher interface Tear bar (tear upwards) Edge guide Platen roller Tear bar Label stop sensor (tear downwards position adjustment and peel-off)) Printhead lift lever Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 20: Connections

    3 Connect the power cord from the socket on the rear plate to an electrical outlet (90 to 265 VAC). Computer The Easycoder PM4i is fi tted with one 9-pin D-style subminiature (DB9) socket for the RS-232 serial interface port (see Appendix C). RS-232 Serial Interface Before you can use the serial interface, you may need to set up the com- munication parameters, such as baud rate, parity, etc.

  • Page 21: Controls And Indicators

    Chapter 2— Installation Controls and Indicators The EasyCoder PM4i has several ways of communicating directly with its operator: three control lamps, a display window, a membrane-switch keyboard with 8 keys and buttons on the printer’s front, and a beeper. Control Lamps...

  • Page 22: Display

    The beeper acknowledges that a key has been pressed. Optionally, an audible alarm can be enabled using an IPL command. It will start beeping at paper out and ribbon out and continue beeping until the start of reload. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 23: Starting Up

    Starting Up This chapter explains how to start up the printer after installation or after having been switched off. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 24: Switching On The Printer

    Initializing When the initialization is completed, a label is fed out. The following message appears, indicating that the printer is ready for operation. IPL 2.10 The message indicates the IPL version number. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 25: Media Load

    • Tear-Off (straight-through) • Peel-Off (self-strip), requires optional integral self- strip unit with liner takeup • Cut-Off (requires optional cutter) • External supply (fan-folds), fan-fold guide available as option Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 26: Tear-Off (Straight-Through)

    Chapter 4—Media Load Tear-Off (Straight-through) The EasyCoder PM4i can print on labels, tickets, tags, and continuous stock in various forms. This section describes the case when the media is torn off manually against the printer’s tear bar. This method is also known as “straight-through printing.”...
  • Page 27 Fold up and adjust the edge guide position. Remove any empty core from so the roll becomes fl ush with the center the media supply roll post. section. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 28 This diagram shows the media path. Adjust the position of the green edge Turn the printhead lift lever counter- guide so the media is guided with a clockwise to engage the printhead. minimum of play. Lock with the nut. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 29 Press the Feed/Pause button to advance the media and adjust the media feed. Tear off the media by pulling it down- wards. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 30: Peel-Off (Self-Strip)

    Chapter 4—Media Load Peel-Off (Self-strip) The EasyCoder PM4i can print on labels, tickets, tags, and continuous stock in various forms. This section describes the case when self-adhesive labels are separated from the liner immediately after printing, which requires optional integral self-strip unit with liner takeup. This is also known as “Self-strip”...
  • Page 31 Pull out the edge guide as far as it goes and fold it down to a horizontal Pull out the handle to collapse the position. Remove any empty core from takeup hub, then remove any liner. the media supply roll post. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 32 Route the liner around the tear bar and of the takeup hub, then rotate the hub the liner drive roller and back under the counterclockwise a few turns to wind up print mechanism and guide shafts. some of the liner. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 33 Adjust the position of the edge guide on guide so the media is guided with a the label slack absorber according to minimum of play. Lock with the nut. the width of the media. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 34 Chapter 4—Media Load Peel-Off , cont. Press the Feed/Pause button to advance Close the front and side doors. the media and adjust the media feed. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 35: Cut-Off

    Chapter 4—Media Load Cut-Off The EasyCoder PM4i can print on labels, tickets, tags, and continuous stock in various forms. This section describes the case when the media is to be cut off by an automatic paper cutter (option). Cut-off can be used for: •...
  • Page 36 Fold up and adjust the edge guide position. Remove any empty core from so the roll becomes fl ush with the center the media supply roll post. section. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 37 This diagram shows the media path. Adjust the position of the green edge Turn the printhead lift lever counter- guide so the media is guided with a clockwise to engage the printhead. minimum of play. Lock with the nut. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 38 Press the Feed/Pause button to advance the media and adjust the media feed. Close the side door and the cutter while The labels can be collected on an pulling the media tight. optional tray. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 39: External Supply (Fanfold)

    Chapter 4—Media Load External Supply (Fan-fold) The EasyCoder PM4i can print on labels, tickets, tags, and continuous stock in various forms. This section describes the case when the media supply is placed behind the printer, usually in the form of fan-folded tickets or tags.
  • Page 40 Chapter 4—Media Load Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 41: Thermal Transfer Printing

    Thermal Transfer Printing This chapter explains how to load the printer with ribbon for thermal transfer printing. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 42: Ribbon Load

    The EasyCoder PM4i can use transfer ribbon rolls wound with the ink- coated side facing either outward or inward. Illustrations in this manual show the ink-coated side facing inward.
  • Page 43 Turn the printhead lift lever clockwise to Open the front and side doors. raise the printhead. In case of ribbon reload, remove any Unpack a roll of original Intermec used ribbon and empty ribbon core. thermal transfer ribbon. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 44 Without releasing the ribbon, turn the Slide the empty cardboard core onto printhead lift lever counterclockwise the ribbon rewind hub so the ribbon to engage the printhead and lock the is wound up when the hub rotates ribbon. counterclockwise. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 45 Turn the printhead lift knob counter- clockwise to engage the printhead. Close the front and side doors. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 46 Chapter 5—Thermal Transfer Printing Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 47: Setting Up The Printer

    It covers the following topics: • Description • Default setup • Setup Parameters in regard of communication, test/ service, media, and confi guration. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 48: Description

    Check the list below to see if the printer’s default setup matches your requirements. If not, you will have to change the setup. To enter the Setup Mode, press the <Setup> key on the printer’s built-in keyboard and follow the instructions in Chapter 7, “Setup Mode.” Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 49: Default Setup

    Paper type Label length 1200 dots Sensitivity Darkness Label rest point Form adj dots X Form adj dots Y Confi guration Emulation None Print speed 4 in/sec Cutter Not installed Label taken sensor Not installed Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 50: Setup Parameters

    • 8 Characters ASCII 000 to 255 decimal (default) Parity The parity decides how the fi rmware will check for transmission errors. There are four options: • None (default) • Even • Odd • Space Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 51: Stop Bits

    XOFF, the printer will resend an XOFF after receiv- ing every 15 characters from the host. Condition Character Buffer already full Printhead raised Ribbon fault No label stock Buffer now full Printhead hot Label at strip pin Label skipping Printing Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 52 Chapter 6—Setting Up the Printer Intermec Standard Protocol The Intermec Printer Standard Protocol is a half-duplex protocol. All data transmissions to the printer consist of status inquiry (ENQ), status dump (VT), or message blocks. Each message block starts with the Start of Text (STX) character and ends with the End of Text (ETX) character.

  • Page 53: Test/Service

    • WINS Name • MAC Address • IP Selection • IP Address • Netmask • Default Router • Name Server • Mail Server • Primary WINS Server • Secondary WINS Server • Network Statistics Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 54: Data Dump

    There are two options. The memory will be reset to factory default as soon as an option has been selected and <Enter> is pressed. Select between “All”, which resets the entire memory and “Confi guration” which just resets the confi guration part of the memory. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 55: Media

    fi rmware can optimize the heating of the print- head and the print speed. Standard supplies from Intermec are labeled with a 3-digit media sensitivity number (see Appendix E) which is used to specify the media grade.

  • Page 56: Darkness

    Form Adj Dots Y Specifi es where the Y-position of the origin should be placed on the label. Allowed range is -30 (closest to the center section) to 30 (furthest from the center section). Default is 0. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 57: Confi Guration

    If the label taken sensor does not work properly, the sensitiviy can be calibrated in the Setup Mode. Select “LTS Calibration” and follow the instructions in the display. Make sure that no direct sunlight or interior lighting interferes with the the label taken sensor. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 58 Chapter 6—Setting Up the Printer Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 59: Setup Mode

    Setup Mode This chapter describes how to navigate in the setup mode, and provides overviews of the Setup Mode. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 60: Navigating In Setup Mode

    Move up one level and escape without changing the setting. Move forward on the same level. Move down one level. Acknowledge and move to next menu. Exit the Setup Mode. Can be used anywhere in Setup Mode. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 61 Mode. The diagram below shows the options in the main loop. Detailed over- views are shown on the pages that follow. Starting point SETUP: SETUP: SER-COM NETWORK Option SETUP: CONFIGURATION SETUP: TEST/SERVICE SETUP: MEDIA Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 62: Setup Mode Overviews

    Scroll back 115200 BAUDRATE; Scroll forward 1200 BAUDRATE; Scroll back 2400 BAUDRATE; 4800 Scroll forward Scroll back Legend: Dotted boxes and lines indicate options. Thick boxes indicates default options. Values inside brackets indicate default settings. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 63 IP ADDRESS NETMASK DEFAULT ROUTER NAMESERVER MAC ADDRESS IP SELECTION: IP ADDRESS: NETMASK: DEFAULT ROUTER: NAMESERVER: MAC ADDRESS: DHCP+BOOTP 192.168.1.79 255.255.255.0 192.168.1.1 192.168.1.7 00104017b80e PARITY: MANUAL PARITY: Read-only Read-only Read-only Read-only Read-only DHCP PARITY: BOOTP Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 64 ALL: PRINT UDC PRINT UDFs Scroll forward PRINT FORMATS PRINT PAGES Scroll back TEST/SERVICE: TEST/SERVICE: DATA DUMP MEMORY RESET DATA DUMP: MEMORY RESET: CONFIG: CONFIG: CONFIGURATION Scroll forward Scroll forward Scroll back Scroll back Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 65 LBL REST POINT: FORM ADJ DOTS X: FORM ADJ DOTS Y: 0/2/4/6/8/10/15/ 0/2/4/6/8/10/15/ 0/2/4/6/8/10/15/ 20/25/30/-30/-25/ 20/25/30/-30/-25/ 20/25/30/-30/-25/ -20/-15/-10/-8/-6/ -20/-15/-10/-8/-6/ -20/-15/-10/-8/-6/ -4/-2 -4/-2 -4/-2 Scroll forward Scroll forward Scroll forward Scroll back Scroll back Scroll back Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 66 86XX-15MIL DISABLE REMOVE LABEL AND 7 IN/SEC PRINT SPPED: Scroll forward Scroll forward PRESS ENTER 8 IN/SEC Scroll back Scroll back <Enter> Scroll forward Scroll back SENSITIVITY 9 OUT OF 8-14 Read only, press<Enter> Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 67 Options This chapter describes the options available for the EasyCoder PM4i printer. The options can be factory installed, fi eld-installed by an authorized service technician, or in some cases installed by the operator. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 68: Introduction

    Chapter 8—Options Introduction The EasyCoder PM4i provides a high degree of fl exibility because it has a modular design. By adding options to the basic printer, the EasyCoder PM4i can be adapted for a variety of applications. Most options should be installed by an authorized service technician or are only available as factory-installed options.

  • Page 69: Integral Liner Takeup Unit

    The Label Taken Sensor (LTS) is a photoelectric sensor that enables the printer’s fi rmware to detect if the latest printed label, ticket, tag, etc. has been removed before printing another copy. The LTS cannot be used in connection with a paper cutter. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 70: Internal Fan-Fold Guide

    A number of interface boards are available for use with the EasyCoder PM4i printer. The interface boards are either factory-fi tted or can easily be fi tted by an authorized service technician. The EasyCoder PM4i can accommodate one EasyLAN interface board plus one IEEE 1284 Parallel Interface Board. EasyLAN boards: •...

  • Page 71: Troubleshooting

    Troubleshooting This chapter lists various possible cases of inferior printout quality, describes possible causes, and sug- gests remedies. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 72: Troubleshooting List

    Change parameter Chapter 6 high Printhead pressure Adjust Chapter 11 too high ☎ Call Service Faulty energy Replace CPU board control Dark lines along Foreign objects on Clean printhead Chapter 10 media path printhead Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 73 Check/change Chapter 11 Dirty sensors Clean media guides Chapter 10 ☎ Call Service Faulty sensors Replace Compressed text or Too high print Lower print speed Chapter 6 bar code speed for large media roll Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 74 Chapter 9—Troubleshooting Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 75 Regular maintenance is important for the printout quality and for the life of the printhead. The chapter covers the following topics: • Printhead cleaning • External cleaning • Cleaning the media guides • Printhead replacement • Media jams Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 76: Printhead Cleaning

    Isopropyl alcohol [(CH CHOH; CAS 67-63-0] is a highly fl ammable, moderately toxic, and mildly irritating sub- stance. Turn the printhead lift lever clockwise to Open the front and side doors. raise the printhead. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 77 Read the Remove any media and transfer ribbon. warning text. Insert most of the cleaning card under the printhead (1). Engage the printhead Pull out the cleaning card (1) and raise (2). the printhead (2). Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 78 fl uid to dissolve the residue. printhead (2). Pull out the cleaning card. If necessary, repeat the process with a fresh cleaning Allow the cleaned parts to dry before card. loading any media (and ribbon). Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 79: External Cleaning

    Never use any sharp tools for removing Never spray the printer. Protect it from stuck labels. The printhead and rollers water when cleaning the premises. are delicate. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 80: Cleaning The Media Guides

    Loosen the screw on the edge guide. Pull both the upper LSS guide and the edge guide straight out. After cleaning, put back the parts in reverse order making sure that the LSS shafts fi ts into the holder on the upper LSS guide. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 81: Printhead Replacement

    While replacing the printhead, the power must be off. The fi rmware will not detect the new printhead resistance until the printer has been restarted. Turn the printhead lift lever clockwise to Open the front and side doors. raise the printhead. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 82 Note the snap-lock on the inner arrows and pull out the printhead as far connector. Pull at the connectors—not as the cables allow. at the cables! Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 83 Turn the printhead lift lever counter- clockwise so the magnet engages the Load a new supply of media and ribbon, printhead bracket. as described earlier in this manual. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 84: Media Jams

    CHOH; CAS 67-63-0] is a highly fl ammable, moderately toxic, and mildly irritating substance. • Reload the media as descibed in Chapter 4. • Switch on the power. • Readjust the media feed by pressing the <Feed/Pause> key. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 85 This chapter describes how the operator can adjust the printer. The chapter covers the following topics: • Narrow media adjustment • Label stop sensor position adjustment • Printhead pressure adjustment • Ribbon break shaft adjustment Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 86: Narrow Media Adjustment

    • After having centered the arm, lock it by tightening the nut. • Remember to adjust all edge guides too. Knurled nut Pressure arm Center of media Edge guide Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 87: Label Stop Sensor Position Adjustment

    • Rotate the screw clockwise to move the sensor towards the center sec- tion. • Rotate the screw counterclockwise to move the sensor outwards, away from the center section. Point of detection Adjustment screw Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 88: Printhead Pressure

    To return to the factory setting, tighten the screw (+) as far as it goes and then loosen it (-) four full turns. Do not use a higher printhead pressure than necessary, because it may increase the wear of the printhead and shorten its life. Adjustment screw Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 89: Ribbon Break Shaft

    (bw) to move the outer end of the break shaft backward. Before readjusting the break shaft, make sure that there is no other cause for the wrinkling of the ribbon. (See Chap- ter 9, “Troubleshooting.”) Adjustment screw Ribbon Break Shaft Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 90 Chapter 11—Adjustments Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 91: Technical Data

    Technical Data This appendix lists the technical data for the printer. Please note that Intermec reserves the right to change without prior notice and that this information does not represent a commitment on the part of Intermec. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 92 20 to 80% non-condensing Electronics Microprocessor 32 bit RISC On-board Flash SIMMs 2 sockets for 4MB or 8MB each Std. 1 x 4MB On-board SDRAM SIMM 1 socket for 8 MB or 16 Mb Std. 8MB Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 93 Liner Takeup operation Rotating Media Supply Option Replaces supply post 3-inch Adapter for Media Option Supply hub only Media Roll Retainer Option Supply hub only Internal Fan-fold Guide Option Side Door with Keylock Option Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 94 External Alphanumeric Option Keyboard CompactFlash Cards Option 8MB-1GB /. The max. print length is also restricted by the amount of free SDRAM memory. /. Latin, Greek, and Cyrillic fonts according to Unicode standard are included. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 95: Media Specifi Cations

    Media Specifi cations This appendix specifi es the physical measures for vari- ous types of media. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 96: Media Roll Size

    Media rolls to be loaded inside the printer should be wound with the printable side facing outwards. The media supply must not be exposed to dust, sand, grit, etc. Any hard particles, however small, can damage the printhead. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 97: Media

    Appendix B—Media Specifi cations Media Non-Adhesive Strip ⇐ a ⇒ Media Width Maximum: 114.3 mm (4.50 inches) Minimum: 25.0 mm (1.00 inches) Media Type Setup • Fix length strip • Var length strip NON-ADHESIVE STRIP Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 98: Self-Adhesive Strip

    ⇐ c ⇒ Media Width (excluding liner) Maximum: 112.7 mm (4.43 inches) Minimum: 23.8 mm (0.94 inches) Media Type Setup • Fix length strip • Var length strip SELF-ADHESIVE STRIP Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 99: Self-Adhesive Labels

    (e) to be larger than 7 mm (0.28 inches), that batch printing is used, and that no pull back of the media is performed. Intermec does not guarantee that such short labels will work, but it is up to the user to test this in his unique application.
  • Page 100 Appendix B—Media Specifi cations SELF-ADHESIVE LABELS FEED DIRECTION Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 101: Tickets With Gap

    (e) to be larger than 7 mm (0.28 inches), that batch printing is used, and that no pull back of the media is performed. Intermec does not guarantee that such short tickets will work, but it is up to the user to test this in his unique application.
  • Page 102 Appendix B—Media Specifi cations TICKETS & TAGS FEED DIRECTION Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 103: Tickets With Black Mark

    Note: The black mark should be non-refl ective carbon black on a whitish background. Do not allow any perforations to break the edge of the media as this may cause the media to split and jam the printer. Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 104 Appendix B—Media Specifi cations TICKETS WITH MARKS FEED DIRECTION Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 105 Interfaces This appendix describes the interface connectors found on the printer’s rear plate. It covers the follow- ing topics: • RS-232 interface • Optional interface boards Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 106: Rs-232 Interface

    Request to send – Not used /. The external +5V is limited to 500 mA and is automatically switched off at overload. Interface Cable Computer end: Depends on computer model Printer end: DB-9pin plug Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 107: Optional Interfaces

    fi tted with one of the following EasyLAN interface boards for connection to a Local Area Network (LAN): • EasyLAN Ethernet Interface • EasyLAN Wireless Interface IEEE 1284 Parallel Interface Board Parallel interface connector EasyLAN Ethernet Interface RJ-45 connector Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 108 Appendix C—Interfaces EasyLAN Wireless Interface EasyLAN antenna Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 109 Supported IPL Commands This appendix lists the IPL commands supported by the printer in alphabetic order. For more information on the commands, refer to the IPL Programming, Reference Manual. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 110: Supported Ipl Commands

    Data Shift - International Characters ...........<SUB> Data Source for Format in a Page, Defi ne ..........e Direct Graphics Mode, Select ............ <ESC>g Emulation Mode, Enter .............<ESC>c Emulation or Advanced Mode on Power-Up ........ <SI>C End-of-Print Skip Distance, Set ...........<SI>D Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 111 Label and Gap Length, Transmit ..........<ESC>L Label Path Open Sensor Value, Transmit ..........L Label Rest Point, Adjust ..............<SI>f Label Retract, Enable or Disable ........... <SI>R Label Retract Distance, Set .............<SI>r Label Stock Type, Select ............... <SI>T Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 112 Remaining Quantity and Batch Count, Transmit ..... <ESC>Q Reset ...................<DLE> Self-Strip, Enable or Disable ............<SI>t Slashed Zero, Enable or Disable ............. <SI>z Software Confi guration Label, Print ............s Start and Stop Codes (Code 39), Print ........ <ESC><SP> Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 113 User-Defi ned Character Field, Create or Edit ........U User-Defi ned Characters, Transmit ..........<ESC>u User-Defi ned Font Character, Create ............ t User-Defi ned Fonts, Print ..............t Warm Boot ..................<BS> Width of Line, Box, Bar, or Character, Defi ne ........w Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 114 Appendix D—Supported IPL Commands Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 115 Intermec Supplies This appendix describes the supplies offered by Intermec for use with this printer, that is, direct ther- mal media, thermal transfer ribbons, and receiving face materials for thermal transfer printing. Intermec EasyCoder PM4i—User’s Guide (IPL version)

  • Page 116: Direct Thermal Media

    Appendix E—Intermec Supplies Direct Thermal Media Intermec offers two quality grades of direct thermal media for the Easy- Coder printers: Premium Quality Top-coated media with high demands on printout quality and resistance against moisture, plasticisers, and vegetable oils. Examples: Europe...

  • Page 117: Thermal Transfer Media

    Appendix E—Intermec Supplies Thermal Transfer Media Intermec offers stock labels for thermal transfer printing in a wide range of quality grades. Uncoated Papers Economical high-volume printing. To be used with GP/TMX 1500 rib- bons. Examples: Europe North America TTR Uncoated –...

  • Page 118: Transfer Ribbons

    Appendix E—Intermec Supplies Transfer Ribbons Intermec offer three ranges of thermal transfer ribbons optimized for dif- ferent purposes: • General Purpose (GP/TMX 1500) transfer ribbons allow high speed printing and give a good printout, but are somewhat sensitive to smearing. They may be the best choice for uncoated and coated papers.

  • Page 119: Setting The Media Sensitivity Number

    Intermed has developed heating schedules (the amount of heat required to image a label) to produce the highest possible print quality for Intermec media and ribbon combinations on Intermec printers. Look for the three-digit media sensitivity number on: • The side of the media roll. Use the last three digits (140 in the exam- ple below) of the 15-digit number stamped on the roll for the media sensitivity number.
  • Page 120 1. At the DOS prompt, type the following command and press Enter: MODE COM1 96,E,7,1,N 2. Type the following command lines and press Enter: COPY CON COM1 <STX><SI>g1,567<ETX>^Z where: sets the media sensitivity number to 567. <SI>g1,567 Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 121 (Plastic) Premium-3/6/7 Duratran Syntran/Premium-3/6/7 European Polyethylene/Premium Duratran Kimdura/Premium-3/6/7 European Duratran Kimdura/ Premium 500 Series Medium Sensitivity Duratran II-1/Premium-3/6/7 (Paper) Duratran II Tag-7mil/ Premium-3/6/7 European Coated/Premium 300 Series Low Sensitivity (Plastic) Super Prem. Poly./Super Prem.-7 Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 122 Appendix E—Intermec Supplies Intermec EasyCoder PM4i—User’s Guide (IPL version)
  • Page 124 Intermec Printer AB Idrottsvägen 10, P.O. Box 123 S-431 22 Mölndal, Sweden tel +46 31 869500 fax +46 31 869595 www.intermec.com EasyCoder PM4i Bar Code Label Printer, User’s Guide (IPL Version) *1-960584-01* *1-960584-01*...

Table of Contents