Kenwood VR-605 Instruction Manual page 18

Preparing for surround sound
l
For VR-615 lHTB model), do not select "LRG" (large) for surround
speaker as this WIII cause the speaker to malfunction.
If you have selected other than "LRG" as the center speaker
setting,
c
0 SURR ON : Surround speaker settrng modetothe receiver IS
ON.
0 SURR OFF : Surround speaker settrng mode to the receiver IS
OFF.
Q Press the SET UP key again to accept the setting.
*The subwoofer re-mix settrng indication "SW RE-MIX" scrolls
across the display.
"SW RE-MIX" scrolls across the drsplay.
l
If subwoofer IS turned OFF, subwoofer re-mix setting IS not
visible.
Q Use the MULTI CONTROL knob or keys to select the
appropriate subwoofer remix setting.
c
0 RMX ON : Subwoofer re-mix set mode to the receiver IS ON.
@ RMX OFF : Subwoofer re-mix set mode to the receiver IS OFF.
@ Press the SET UP key to accept the setting.
*The receiver enters the speaker volume level adjustment
mode.
l
In step a and a, indications appear only for the selected
channels of the speakers that require adfustrng.
a Adjust the speaker volume level.
From Your usual listening posrtion, adjust the volume levels. The
volume levels from each speaker should be the same.
0 Press the SET UP key to begin TEST TONE.
c
0 AUTO
0 MANUAL
0 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or keys.
PresstheSETUPkeyagaintoselecteitherAUTOorMANUAL.
Use the MULTI CONTROL knob or keys to adjust the volume
lev,el of the test tone output from the speaker channel to be
adjusted.
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
L+C-,R+SR+SL+SW
The channel indication blinks while the test tone is berng ouput.
l
If you change the volume level settings for the speakers whrle
listenrng to musrc, the settings referred to on this page are also
changed.
-m -
l
If the speaker setting selects are OFF, the speaker level settings
are reset.
Q Press the SET UP key.
l
The test tone is turned off. The receiver enters the mode for
inputting the distance to the speakers.
0 For MANUAL selection, press the SET UP key each time to
select the speaker channel.
m Input the distance to the speakers.
0 Select the DISTANCE from the set up displays and press the
SET UP key again.
0 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers : _ feet (meters)
Distance to center speaker _ feet (meters)
Drstance to surround speakers
_ feet (meters)
Q Use the MULTI CONTROL knob or keys to select the distance
to the front speakers.
The speaker rndrcator to be adjusted blanks.
Indication in feet
lndrcatron rn meters
l
The allowable settrng range IS 1 to 30 feet (0 3m to 9.0m).
adjustable rn 1 foot (0.3m) Increments.
Q Press the SET UP key to accept the settings.
0 Repeat steps Q and 0 to input the distance for each of the
speakers.
0 Setup is complete when the input indication appears.
l
The speakers You have selected should appear on the display
Confirm that all the speakers have been correctly selected.
0 Press the SET UP key to exit the SET UP mode.
Input level adjustment (analog sources only)
If the Input level of an analog source srgnal IS too hrgh. the CLIP indrcator
wrll blink to indicate the source signal. Adfust the Input level
0 Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
l
You can store a separate Input level for each Input source.
Q Press the SOUND key repeatedly until the "INPUT" indication
appears.
0 Use the MULTI CONTROL knob or keys to adjust the input level.
*The adjustment mode is displayed for approxrmately eight sec-
onds.
l
The Input level may be adjusted to any one of three settings: OdB,
-3dB. and -6dB. (The Initial setting IS 0dB.f
0 Press the SOUND fey again to return to the input indication.
18EN