Download  Print this page

Kenwood VR-605 Instruction Manual page 33

Audio video surround receiver
Hide thumbs

Advertisement

In case of difficulty
Resetting the Microcomputer
The microcomputer
may malfunction
(unit cannot be operated,
or shows an erroneous
display) if the power cord is unplugged
while the power is ON, or due to some other external factor.
If
this happens,
execute
the following
procedure
to reset the
microcomputer
and return
th)
unit to its normal
operating
condition.
l
Please note that I esettlng the mrcrocomputer WI/I clear the contents
of the memory and return the unit to the state It was rn when It left
the factory
For the U.S.A. and Canada
Unplug the power cord from the wall outlet, then
plug it back in while holding down the POWER key.
For other countries
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY
0
key, press POWER.
mplifier
~~~~~~~
No sound from the speakers.
l
Connect them properly refemng to "Connect-
ing the speakers"
-m
l
Adjust the volume to a proper level.
l
Turn OFF the MUTE.
-@j
l
Set the SPEAKERS swatch to ON.
42%
l
Turn the power off, elrmrnate the short-circuit-
rng, then turn on the power agarn.
l
The speaker cords are drsconnected.
l
VOLUME IS set to the m~nrmurn posrtron
l
MUTE IS ON
l
The SPEAKERS swatches are set to OFF
The standby
indicator
blinks and sound is
not output.
l
Speaker cords are short-crrcuited.
Sound is not output from one of the speak-
ers.
l
The speaker cord IS disconnected.
l
Connect It properly referrrng to "Connecting
the speakers".
-ml
l
Connect It properly referring to "Connectrng
the speakers".
-EL
l
Select a surround mode.
l
Adjust the speaker levels using the test tone.
-m
l
Insert the audio cord plugs securely Into the
PHONO jacks.
l
Connect the groundrng wrre to the GND termr-
nal on the rear panel
l
Set the Input mode to drgrtal manual before
startrng playback of the Dolby Digital source.
-m
l
Press the INPUT MODE key to select to digital
auto mode.
-c?z
l
Copy-guarded vrdeo software
cannot be re-
corded
Sound
is not output
from
the surround
speakers and I or the center speaker, or their
sound is very small.
l
The surround speaker cords and/or the center
speaker cord IS drsconnected
l
A surround mode has not been engaged
l
The surround and/or center volume controls
are set to the mrnrmum level.
l
The audro cord from the record player IS not
connected to the PHONO lacks.
l
The record player IS not grounded
l
There are many possrble causes for thus prob-
lem, dependrng on the type of DVD player
used
A humming
noise is generated
when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
l
The Input tnode IS set to drgrtal manual
A video source cannot be recorded normally.
l
The software IS copy-guarded
Radio stations
cannot be received.
l
No antenna IS connected
*The broadcast band IS rnot set properly.
*The frequency of the desrred station IS not
tuned
l
Connect an antenna
l
Set the broadcast band properly.
l
Tune the frequency of the dewed station.
-iz
Interference.
l
Norse due to rgnrtron norse from an automo-
brie
l
Noise due to Interference
from an electrrc
appliance
l
Noise due to a nearby TV set
l
Install the outdoor antenna away from the
road
l
Turn off the power to the applrance.
l
Install the recerver farther away from the TV.
A station
which was preset cannot
be re-
ceived by pressing
the corresponding
nu-
meric key.
l
The preset statron belongs to a frequency that
cannot be recerved
* The preset memory was cleared because the
power cord lhad been unplugged for a long
period of time
l
Preset a statron with a receivable frequency.
l
Preset the station again
33 EN

Hide quick links:

Advertisement

loading

  Also See for Kenwood VR-605

  Related Manuals for Kenwood VR-605

This manual is also suitable for:

Vr-615Krf-v5060dKrfw4060dKrfw5560dKrf-v4060dKrf-v5560d