Normal Playback; Preparing For Playback; Input Level Adjustment (Analog Sources); Selecting The Input Mode - Kenwood VR-507 Instruction Manual

m input the distance to the speakers.
0 Measure the distance from the listenmg position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers: _ feet (meters)
Distance to center speaker:
_ feet (meters)
Distance to surround speakers: _ feet (meters)
0 Use the MULTI CONTROL knob or keys to select the dis-
tance to the front speakers.
The speaker Indicator to be adjusted blinks.
\\I//-
%Ql-~ jq m,-*-ii"" . . . . . . ,, ::: ::
//a\ i I,,.,, i : " ::-: . ,,.,. i i
STEREO
I
Indication In feet Indication In meters
l
The allowable setting range IS 1 to 30 feet (0.3 to 9.0 m), adjustable
In 1 foot (0.3 m) Increments.
Q Press the SET UP key to accept the settings.
0 Repeat steps 0 and Q to Input the distance for each of the
speakers.
@ Setup IS complete when the Input mdication reappears.
"""
Display when all speakers have been selected.
l
The speakers you have selected should appear on the display
Confirm that all the speakers have been correctly selected.
If the Input level of an analog source slgnal IS too high, the CLIP
Indicator will blink to Indicate the source slgnal. Adjust the Input level
AD-
CUP
0 Use the INPUT SELECTOR knob to select the source of
which the input level you want to adjust.
l
You can store a separate Input level for each Input source. If the
MONITOR functiQn IS ON, you can store an Input level for when
MONITOR IS on Independently of the Input levels for the Input
sources.
0 Press the SOUND key repeatedly until the "INPUT" indication
appears.
0 Use the MULTI CONTROL knob or keys to adjust the input level.
l
The adjustment mode IS displayed for approximately eight
seconds.
l
The Input level may be adjusted to any one of three settings: OdB,
-3dB, and -6dB. The Initial setting IS OdB.)
0 Press the SOUND key again to return to the input indication.
Preparing for playback
SPEAKERS A/B
If you have selected a component connected to the
CDIDVD, VIDE02,
VIDEO3
or
DVD/Gch
jacks, make sure that the Input mode setting IS
correct for the type of audio slgnal to be used.
-m
,. 9-,~~~~~~~~~. *I_ *.t*
6&\ "i.7aTs~~~
j_
. . * ..~
Sefecthtg ~O~~F~
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting
IS "TAPE"
To change
the source to
"MD,"
follow the steps below:
0 Use the INPUT SELECTOR knob to select "TAPE"
0 Hold down the AUTO/CINEMA EQ. key for more than 2
seconds.
l
The source Indication changes to
"MD"
l
To return to the onglnal Indication, repeat procedure 0.
Press the SPEAKERS A or B key to select the speaker system
to be used.
AON
BON
A+B ON
A+B OFF
Sound from the speakers connected to the
SPEAKERS A
terminals on the rear panel.
Sound from the speakers connected to the
SPEAKERS B
terminals on the rear panel. No sound will be heard from
the subwoofer.
Sound from both the speakers connected to the
SPEAKERS A
and
B
terminals on the rear panel.
No sound from the speakers. Use this setting when
listening with headphones for stereo sound in all playback
modes.
The Indicator for the speakers
you want to use should be lit.
l
Selecting "6ch INPT" by pressing the
INPUT MODE
key, whereby "DVD/
6ch" is the Input source will cause
SPEAKER A
to be selected automati-
cally.
'iur~in~ on ihe receiver
'.
..~ \
@ Turn on the power to the related components.
0 Turn on the power to this receiver by pressmg POWER and
ON/STANDBY keys.