Normal Playback; Preparing For Playback - Kenwood KRF-V7030D Instruction Manual

4
Input the distance to the speakers.
16
1 Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
Distance to center speaker:
Distance to surround speakers:
2 Use the MULTI CONTROL to select the distance to the front
speakers.
The speaker indicator to be adjusted blinks.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP key.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
5 Setup is complete when the input indication reappears.
SP A B TI.VOL
L
CLIP MUTE
LFE
RDS EON PTY
LS
TP TA NEWS
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all
the speakers have been correctly selected.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level.
1 Use the INPUT SELECTOR knob to select the source who's
input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key several times until the "INPUT" indication
appears.
3 Use the MULTI CONTROL to adjust the input level.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0,
-3, and -6. (The initial setting is 0.)
4 Press the SOUND key to return to the input indication.
Preparing for surround sound
____ feet (meters)
____ feet (meters)
____ feet (meters)
FM AUTO SOUND
AM PRO LOGIC
MHz 3 STEREO
kHz DOWN MIX
Indication in meters
C R
SW
S RS
FM AUTO SOUND
AM PRO LOGIC
MHz 3 STEREO
kHz DOWN MIX

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
ON/STANDBY
DIGITAL AUTO
POWER
S.DIRECT MEMO
ST.
MONITOR
TUNED
DSP
Selecting the input mode
If you have selected a component connected to the CD, DVD, VIDEO2,
or VIDEO3 (KRF-V7030D only) jacks, make sure that the input mode
setting is correct for the type of audio signal to be used.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "TAPE". To change the
source name associated with the MD/TAPE jacks to "MD," follow the
steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO key for more than 2 seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control to
"MD".
Selecting the speaker system (except for KRF-V5030D/
V4530D)
Press the SPEAKERS A or B key to select the speaker system to
be used.
A ON : Sound from the speakers connected to the SPEAKERS A
B ON : Sound from the speakers connected to the SPEAKERS B
A+B ON : Sound from both the speakers connected to the SPEAKERS
A+B OFF : No sound from the speakers. Use this setting when listening
The indicator for the speakers
you want to use should be lit.
SP A B TI.VOL
CLIP MUTE
RDS EON
TP TA NEWS
DIGITAL AUTO
KRF-V7030D/V6030D
S.DIRECT MEMO
MONITOR ST.
DSP TUNED
• Activating a surround mode or selecting "DVD/6ch" as the input
source causes speaker system A to be selected automatically.
On the KRF-V5030D/V4530D, press the SPEAKER key to switch the
speakers on and off.
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER and ON/
STANDBY keys.
INPUT MODE
AUTO
INPUT SELECTOR
SPEAKERS A/B
terminals on the rear panel.
terminals on the rear panel.
A and B terminals on the rear panel.
with headphones for stereo sound and virtual surround in all
playback modes.
The speaker indicator lights.
SP A
L C R
CLIP
LFE SW
PTY RDS EON
LS S RS
TP TA
KRF-V5030D/V4530D
0
RC1
B TI.VOL
L C R
MUTE
LFE SW
PTY
LS S RS
NEWS