Searching For Your Code; Checking The Codes; Re-Assigning Device Keys - Kenwood VR-507 Instruction Manual

Searching for your code Re-assigning device keys
If your component does not respond after tryrng all the codes listed for your
component, or if your component IS not listed at all, try searchrng for your
code.
For example, to search for a code for your TV:
The remote control can be set up to control a second TV or VCR, or any
combrnation of erght home entertarnment components.
For example, to control a TV a Cable Converter, and two VCRs usrng the
remote control,you will need to re-assrgn the unused CD key to operate the
second VCR as follows:
a Press the TVkey once. Next, press and ho/d the SET UP
key until the LED blinks twrce, then release fhe SET UP
key.
H Press the numer/c key to enter "9 - 9 - 1"
l
The LED will blink twrce.
a Pomt the remote control at the TV and slowly alternate
between pressmg the POWER and TV keys.
l
Stop when the TV turns ON/OFF
l
In the search mode, the remote control will send IR codes from its
librarytotheselected devrce, starting with themost popularcodefirst.
0 Press the SET UP key once fo lock m the code.
q
To search for the codes of your other components, repeat
steps
q
through H, but substitute the approprrafe key
(i.e., DVD, CBL, VCR, TV, DSS, CD or RECEIVER) for the
component you are searchmg for.
Checking the codes
* a
If you have set up the remote control usrng the procedures described In
"Searchrng for your codes", you may need to find out whrch four-digit
code IS operating your equrpment:
For example, to find out whrch code IS operating your TV:
q
Press fhe TV key once. Next, press and hold the SET UP
key until the LED blinks twrce, then release the SET UP
key,
m Press the numeric key to enter "9 - 9 - 0"
l
The LED will blink twrce.
q
To tvew the code for the first digit, press "7 " once. Waif
for 3 seconds, count the number of times the LED blinks
(e.g., blinks = 3) and write down that number.
l
If a code digit IS "O", the LED will not blink.
a Repeat step 0 three more times for the remarnrng digits.
Use "2" tar the second dtgif, "3" /or the fhrrd digit, and
"4" for the tourfh digit.
q
To check the codes of your other components, repeaf
steps 0 through 8, but substitute the appropriate key
(i.e., DVD, CBL, VCR, TV, DSS, CD or RECEIVER) for the
component you are checking.
l
As suggested earlier on, write down each of the four- digit code.
q
Press and ho/d the SET UP key until fhe LED b/inks twice,
then release the SET UP key.
B Press the numerfc key to enter "9 - 9 - 2"
l
The LED will blink twrce.
IE) Press the VCR key once, then press fhe CD key once.
q
To re-asslgn other dewce keys, repeat steps 0 fhrough
q
by subsfitufing fhe key sequence from the below chart
for the most popular components:
To re-asslgn key
sequence
Perform
TV as 2nd VCR key
SETUP-9.9-2.VCR-TV
TV as 2nd CBL key
SETUP-9-9.2-CBL-TV
TV
as 2nd RECEIVER key
SETUP - 9 - 9 2 - RECEIVER -TV
TV as 2nd CD key SETUP-9-9-2.CD-TV
TV back to TV SETUP-9-9.2-TV-TV
VCR as 2nd TV key SETUP-9.S-2.TV-VCR
VCR as 2nd CBL key SETUP-9-S-2-CBL-VCR
VCR as 2nd RECEIVER key SETUP 9 - 9 - 2 - RECEIVER -VCR
VCR as 2nd CD key SETUP-9-9.2-CD-VCR
VCR back to VCR SETUP-9-9.2-VCR-VCR
l
When a re-assrgnment IS done, the LED will blink twrce to confirm your
chorce. At that time, you will need to program the remote control rn
order to control the new component.