Normal Playback; Preparing For Playback - Kenwood 5.1 KRF-V7050D Instruction Manual

20
4
Input the distance to the speakers.
1 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
Distance to center speaker:
Distance to surround speakers:
2 Use the MULTI CONTROL knob or keys to select the dis-
tance to the front speakers.
The speaker indicator to be adjusted blinks.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP key to accept the settings.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
5 Setup is complete when the input indication reappears.
SP A B TI.VOL
L
CLIP MUTE
LFE
RDS EON PTY
LS
TP TA NEWS
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP
indicator will blink to indicate the source signal. Adjust the input level.
CLIP
RDS
TP
1 Use the INPUT SELECTOR knob to select the source of
which the input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key repeatedly until the "INPUT" indication
appears.
3 Use the MULTI CONTROL knob or keys to adjust the input level.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
• The adjustment mode is displayed for approximately eight
seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
Preparing for surround sound
____ feet (meters)
____ feet (meters)
____ feet (meters)
FM AUTO SOUND
AM PRO LOGIC
STEREO
MHz 3 STEREO
kHz DOWN MIX
Indication in meters
C R
SW
S RS
FM AUTO SOUND
AM PRO LOGIC
STEREO
MHz 3 STEREO
kHz DOWN MIX

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
ON/STANDBY
POWER
(KRF-V7050D)
DIGITAL AUTO
S.DIRECT MEMO
ST.
MONITOR
DSP TUNED
Selecting the input mode
If you have selected a component connected to the CD/DVD, VIDEO2,
VIDEO3 or DVD/6ch jacks, make sure that the input mode setting is
correct for the type of audio signal to be used.
Selecting MD/TAPE
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting is "TAPE". To change
the source to "MD," follow the steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO/CINEMA EQ. key for more than 2
seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat procedure 2.
Selecting the speaker system
Press the SPEAKERS A or B key to select the speaker system
to be used.
A ON : Sound from the speakers connected to the SPEAKERS A
B ON : Sound from the speakers connected to the SPEAKERS B
A+B ON : Sound from both the speakers connected to the
A+B OFF : No sound from the speakers. Use this setting when
• Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/
6ch" is the input source will cause SPEAKER A to be selected automati-
cally.
DIGITAL AUTO
S.DIRECT MEMO
ST.
MONITOR
TUNED
DSP Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER and
ON/STANDBY keys.
INPUT MODE
AUTO/CINEMA EQ.
INPUT SELECTOR
SPEAKERS A/B
terminals on the rear panel.
terminals on the rear panel. No sound will be heard from
the subwoofer.
SPEAKERS A and B terminals on the rear panel.
listening with headphones for stereo sound in all playback
modes.
The indicator for the speakers
you want to use should be lit.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
9