Preparing For Surround Sound; Speaker Settings - Kenwood VR-507 Instruction Manual

To enable you to obtatn optimum enjoyment from the recerver's listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
MULTI CONTROL
1 SET UP
POW-ER
(KRF47050)
ON/STANDBY
K-R0720
a Turn on the power to t/us receiver by pressmg
POWER (I /c!I) key.
a Select a speaker system.
8 Press the SET UP key such that the subwoofer setting
mdication "SUBW ON" appears.
0 Use the MULTI CONTROL knob or keys to select the appro-
pnate subwoofer setting.
c
@
SUBW
ON: Subwoofer setting mode to the recetver IS ON.
@ SUBW OFF:
Subwoofer setting mode to the recerver IS OFF
l
The Initial setting IS "SUBW ON"
l
When the setting "SUBW OFF" IS selected, the front speakers are
automatically set to "FRNT LRG" and the procedure skrps to step 0.
l
When subwoofer output sound IS requrred, select "FRNT NML"
0 Press the SET UP key to accept the setting.
l
The front speakers setting Indication "FRNT" appears
Q Usethe MULTI CONTROL knob or keys to select the approprr-
ate front speakers setting.
0
FRNT NML
(normal): Average stze front speakers are
connected to the receiver.
$l FRNT LRG
(large): Large front speakers are con-
nected to the recetver.
l
For "FRNT LRG" selection, no sound will be heard from SUBW
even when it IS set to ON. However, if you select CINEMA EQ when
subwoofer IS selected, you will be able to hear sound from the
subwoofer.
When In STEREO mode, the sound goes directly to front speaker.
0 Press the SET UP key to accept the setting.
*The center speaker setting Indication "CNTR" appears
0 Use the MULTI CONTROL knob or keys to select the approprrate i
center speaker setting.
If you selected "LRG" as the front speakers setting,
r
0 CNTR LRG
(large): A large center speaker IS connected to
the receiver.
@
CNTR NML
(normal):
An averagesrze center speaker IS con-
nected to the recerver.
@ CNTR OFF* Center speaker setting mode to the
recetver IS OFF
If you have selected "NML" as the front speakers setting,
c
(3 CNTR ON:
Center speaker setting mode to the receiver IS
ON.
@
CNTR OFF.
Center speaker setting mode to the receiver IS
OFF
0 Press the SET UP key agam to accept the setting.
*The surround speaker setting Indication "SURR" appears
0 Use the MULTI CONTROL knob or keys to select theapproprrate
surround speaker setting.
If you selected "LRG" as the center speaker setting,
L
@ SURR LRG
(large): Large surround speakers are con-
nected to the receiver.
@
SURR NML
(normal): Average size surround speakers are
connected to the receiver.
@ SURR OFF.
Surround speaker setting mode to the
recerver IS OFF
If you have selected other than "LRG" as the center speaker
setting,
0 SURR ON:
Surround speaker setting mode to the recerver
IS ON.
@
SURR OFF-
Surround speaker setting rnode to the receiver
IS OFF
0 Press the SET UP key again to accept the setting.
l
The receiver enters the speaker volume level adjustment mode.
l
In steps
q
and a, rndications appear only for the selected channels
of the speakers that requtre adjusting.
a Adjust lhe speaker volume /eve/.
From your usual listentng position, adjust the volume levels. The
volume levels from each speaker should be the same.
0 Use the MULTI CONTROL knob or keys to adjust the volume
level of the test tone output from the speaker channel to be
adjusted.
The channel Indication blinks while the test tone IS betng output.
The test tone
IS
heard from the speakers m the following
sequence for 2 seconds each:
~L+C+R+SR+SL+SW~
l
If you change thevolume level settings for the speakers while lisientng
to mustc, the settings referred to on thts page are also changed.
-GZ
l
If the speaker setting selects are OFF, the speaker level settings are
reset,
Q Press the SET UP key.
l
The test tone IS turned off. The recerver enters the mode for Inputting
the distance to the speakers.
Continued to next page