Usb Connections; Grounding (Earthing); Factory Reset Switch; Connections Guideline - Ness IQ User Manual

1.5.11 USB Connections

There are up to four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or
a mouse to control the device.
1.5.12 RS-232 Connections
This port is not in use for users. Do not connect any devices through this This port is not in use for users. Do not connect any devices
CAUTION
WHEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR
SERVICE REPRESENTATIVE.

1.5.13 Grounding (Earthing)

Connection of ground wire is highly recommended to protect the DVR from external electric shock, such as lightening, Connection of ground wire is highly recommended to protect the DVR from external
electrical surge.

1.5.14 Factory Reset Switch

Reset the switch to restore all setup values of menus to factory default settings. It is also possible to use to initialize System Reset the switch to restore all setup values of menus to factory default settings. It is also
Log file.
The switch is located in a pin hole of the back panel. The switch is located in a pin hole of the back panel.
Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked. Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked. Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked.
CAUTION
PRESS FACTORY RESET SWICH ONLY IN LIVE MODE RESS FACTORY RESET SWICH ONLY IN LIVE MODE NEVER PRESS IN SETUP MODE.
1.5.15 Power Supply connections Power Supply connections
4 / 8 Channel:960H & 4 Channel SDI 960H & 4 Channel SDI
to 'DC12V' connector and plug another side to ' connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction. Please do not use any different power supply adapter because it may cause the DVR to malfunction. Please do not use any different power supply adapter because it may cause the DVR to malfunction.
16 Channel 960h & 8 / 16 Channel SDI 960h & 8 / 16 Channel SDI
to 'DC12V' connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC). ' connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC). ' connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction. Please do not use any different power supply adapter because it may cause the DVR to malfunction. Please do not use any different power supply adapter because it may cause the DVR to malfunction.

1.5.16 Connections Guideline

Video Out Connector: If only the monitor is connected to
rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images. If wish to connect another devi rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images.
a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to HIGH Z (High a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to
Impedance) and set the last device to 75 ohms. Impedance) and set the last device to 75 ohms.
Alarm Input Connector: Do not input any type of voltage to the AI 1~AI
Digital Video Recorder for Ness IQ-Series
Plug the power supply adapter (DC 12V, 5A) which include in this product
power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
: Plug the power supply adapter (DC 12V, 6.67A)
If only the monitor is connected to VIDEO OUT connector, please set the impedance switch on the
Do not input any type of voltage to the AI 1~AI4 (AI 16) connectors.
Series 960H & SDI DVR
port.
VIDEO OUT connector, please set the impedance switch on the
c shock, such as lightening,
possible to use to initialize System
which include in this product
A) which include in this product
If wish to connect another device (e.g.,
Page 14