Table of Contents
Advertisement
Printout of status and help list from the camera.
The below lists shows printout from a hyperterminal.
Fpga Init. NG
COMPLETE
ST?
SM=2
SH=2
PE=791
PER=250
PEG=250
PEB=250
TR=0
SL=0
LS=1
RF=1
TI=0
TP=0
SC=0
BI=0
BA=1
CBAR=0
WB=0
GA=0
GAR=0
GAB=0
BLG=0
BLR=0
BLB=0
KN=1
KSR=2048
KSG=2048
KSB=2048
KPR=890
KPG=890
KPB=890
WA=0
SDM=1
VN?
VN=100
PV?
PV=37
ID?
ID=A100016683
MD?
MD=
UD?
UD=
CV-M9 CL
hp?
*** CV-M9 Camera Control Help List *******************************
EB(echo back): 0=off, 1=on
ST(status request): return the all settings
VN(firmware version request): return the version no. of firmware
UD(user ID request): return 16 letters of user ID
SM(Shutter Mode): 0=preset shutter (RGB common set), 1=programmable exposure
(RGB common set), 2=programmable exposure(RGB individual set)
SH(Shutter Speed): 0=off, 1=1/60, 2=1/100, 3=1/120, 4=1/250, 5=1/500
6=1/1000, 7=1/2000, 8=1/4000, 9=1/10000, 10=1/16000, 11=1/50000
PE(programmable exposure)(RGB common set): 0-791
PE(programmable exposure)(RGB common set): 0-791
PER(programmable exposure for Red): 0-791
PEG(programmable exposure for Green): 0-791
PEB(programmable exposure for Blue): 0-791
TR(trigger mode): 0=normal, 1=edge pre-select, 2=pulse width control
3=sensor gate control, 4=reset continuous
SL(smearless mode): 0=off, 1=on
LS(lval synchronous accumulation): 0=sync., 1=async.
RF(rct fval type): 0=cameralink, 1=JAI standard
TI(trigger input): 0=camera-link, 1=hirose 12pin
TP(trigger polarity): 0=active low, 1=active high
SC(scanning format): 0=full frame, 1=1/2 partial, 1=1/4 partial, 1=1/8 partial
BI(binning): 0=binning off, 1=v binning
BA(output bit allocation): 0=10bit, 1=8bit
CBAR(color bar): 0=off, 1=on
WB(white balance): 0=manual/one push, 1=continuous, 2=3200K, 3=4600K, 4=5600K
GA(master gain level): -132-429
GAR(red gain level): -231-231
GAB(blue gain level): -231-231
AW(one push white balance): 0=one push
BLG(green black level): 0-1023
BLR(red black level): 0-1023
BLB(blue black level): 0-1023
KN(knee on/off): 0=on, 1=off
KSR(knee slope for red): 1-4095
KSG(knee slope for green): 1-4095
KSB(knee slope for black): 1-4095
KSR(knee point for red): 0-1023
KSG(knee point for green): 0-1023
KSB(knee point for black): 0-1023
SDM(shading mode): 0=on, 1=off
LD(Load settings from Flash memory): 0=factory, 1=user1, 2=user2, 3=user3
SA(Save settings in Flash memory): 1=user1, 2=user2, 3=user3
WA(Set auto white sampling Area): 0=full, 1=upper left, 2=upper middle,
3=upper right, 4=middle left, 5=middle, 6=middle right,
7=lower left, 8=lower middle, 9=lower right,
AWRS(Request one push W.Bal. result): 0=complete, 1=too bright, 2=too dark,
3=timeout, 4=busy, 5=limit,
*** Firmware Version 1.00 ***** Copyright(c) 2003-2004 JAI Corporation *****
Fig. 33. Terminal printout of status, ID and Help.
- 28 -
Advertisement
Table of Contents
