Activating/Deactivating The Sms Function; Self-Help With Errors - Siemens Gigaset 5030 Quick Manual

Adding the number of the message sender to the directory
You are reading an SMS (page 12).
B
Press the OK key.
AB
Select
Save Address
Continue, see page 4.
Setting the validity period
Sent SMS are stored temporarily in the SMS centre. If it is not
possible to deliver an SMS, e.g. because the receiver's tele-
phone is not switched on, the SMS is stored in the centre for
the validity period and repeated attempts to deliver are
made. If the SMS cannot be delivered within the validity
period, it is deleted at the SMS centre and is not delivered.
¢
F
SMS/CLIP Setup
AB
Select validity period (1, 12, 24 or 72 hrs.).
Press the OK key.
Activating/deactivating automatic reply
If no CLIP is transmitted to your line, you can adjust the set-
ting so that the attempted delivery of an SMS will be
answered automatically by the SMS centre after a specified
number of ringtones (default setting: Disable).
¢
F
SMS/CLIP Setup
AB
Select the ringtone frequency
(Disable, 2, 3, 4, 5, 8 or 9).
Press the OK key.
SMS to a PABX
◆
You can only receive an SMS when the Calling Line
Identification is forwarded to the extension of the
PABX (CLIP). The CLIP evaluation of the number of the
SMS centre takes place in your telephone.
◆
Depending on your PABX, you may have to add the
access code (external line prefix) before the number of
the SMS centre. You can store the access code in your
telephone.
If in doubt, test your PABX e.g. by sending an SMS to
your own phone number, once with and once without
the access code.
◆
When you send text messages, your sender number may
be sent without your extension number. In this case, the
recipient cannot reply to you directly.
Sending and receiving SMS on ISDN PABXs is only possible
via the MSN number assigned to your telephone.

Activating/deactivating the SMS function

When you switch off you cannot send or receive any text
messages with your phone.
. Press the OK key.
¢
Valid Period
¢
Auto Answer
13
GB
Settings which you have made for sending and receiving
text messages (the numbers of SMS centres) and any entries
in the incoming message and draft message lists will be
retained even after the function is deactivated.
¢
F
SMS/CLIP Setup
A C
/ Activate: select Yes (default setting);
Deactivate: select No.
B
Press the OK key.

Self-help with errors

The following table lists error situations and possible causes
and provides notes on troubleshooting.
You cannot send messages.
1. You have not requested the CLIP service (Calling Line
Identification Presentation).
Ask your service provider to enable this service.
2. Text message transmission has been interrupted (e.g. by a call).
Re-send the text message.
3. The feature is not supported by the network provider.
4. No number or an invalid number is entered for the SMS centre
activated as the send centre.
Enter phone number (page 10).
You receive a message whose text is incomplete.
1. Your phone memory is full.
Delete old messages (page 12).
2. The service provider has not yet sent the rest of the message.
You have stopped receiving messages.
Call forwarding is activated with CFU or call forwarding CFU is
activated for the T-Net box.
Change your call forwarding.
The message is played back.
1. The "display call number" service is not activated.
Have your service provider enable this service (there is a charge
for this).
2. Mobile phone operator and network SMS service provider have
not agreed on a cooperation.
Obtain information from your network SMS service provider.
3. The end device is stored in your SMS provider's database as not
having fixed network SMS functionality, i.e. you are no longer
registered there. Register the terminal (again) for SMS recep-
tion.
Messages are only received during the day.
1. The terminal is stored in your SMS provider's database as
not having fixed network SMS capability, i.e. you are no longer
registered there.
Register the terminal (again) for SMS reception (see above).
¢
SMS Service