Basic Operation; Operation Procedures; Recorder Operation - Marantz PM5003 User Manual

BASIC OpERATION

OpERATION pROCEdURES

q
INPUT SELECTOR
STANDBY
POWER ON/OFF
PHONES
operate each equipment to start play.
7 To play an analog disc
1.
set the INpUT SELECTOR switch q to
Phono.
2.
Play a disc on the turntable.
3.
adjust the volume with the VOLUmE control
w and adjust the tone with the BASS and
TREBLE controls e.
NOTES:
• set the VOLUmE control to the minimum
position before placing the stylus on the disc or
before replacing the cartridge.
• do not apply shock or vibration to the turntable
during play, as this may cause the stylus to jump
and the analog disk to be damaged.
• if the turntable is installed too close to the
speakers, the volume may not be able to be
increased to a high level due to howling.
• do not switch the power oFF while the stylus is
on the disc surface.
w
INTEGRATED AMPLIFIER PM5003
PHONO TUNER CD AUX/DVD 1 RECORDER 2 MUTE
VOLUME
SOURCE DIRECT A SPEAKERS B LOUDNESS
BASS TREBLE BALANCE
MIN MAX
L R
e
7 To listen to Fm/Am broadcasts
1.
set the INpUT SELECTOR switch q to
TunEr.
2.
Tune in the desired station on the tuner.
3.
adjust the volume with the VOLUmE control
w and adjust the tone with the BASS and
TREBLE controls e.
7 To play a Cd
1.
set the INpUT SELECTOR switch q to Cd.
2.
Play a Cd on the Cd player.
3.
adjust the volume with the VOLUmE control
w and adjust the tone with the BASS and
TREBLE controls e.
7 To play a dVd or component
connected to AUX/dVd jacks
The component connected to the AUX/dVd jacks
on the rear panel can be played as follows.
1.
set the INpUT SELECTOR switch q to AUX/
dVd.
2.
Play the component connected to the selected
input.
3.
adjust the volume with the VOLUmE control
w and adjust the tone with the BASS and
TREBLE controls e.

RECORdER OpERATION

A
PHONO
INPUT SELECTOR
BASS
STANDBY
POWER ON/OFF
PHONES
Control used for operating the tape deck.
7 pLAYBACK
1.
set the INpUT SELECTOR switch
RECORdER 1 (Cd-R) or RECORdER 2 (md/
TApE).
2.
Play a prerecorded disc or tape on the
recorder.
3.
adjust the volume with the VOLUmE control
B .
4.
adjust the tone with the BASS and TREBLE
C
controls .
7 RECORdING
The playback sound of a program source component,
such as a turntable, a tuner, or a Cd player, can be
recorded on disc or tape as followss.
1.
set the program source component with the
A
INpUT SELECTOR switch .
2.
Play the program source.
3.
operate the recorder(s) to record the playback
sound on disc(s) or tape(s).
B
INTEGRATED AMPLIFIER PM5003
TUNER CD AUX/DVD 1 RECORDER 2 MUTE
VOLUME
SOURCE DIRECT A SPEAKERS B LOUDNESS
TREBLE BALANCE
MIN MAX
L R
C
7 COpYING
You can copy between two recorders connected to
Pm5003.
1.
A select the program source rECordEr 1 with
to
the INpUT SELECTOR switch
2.
The rECordEr 1 signal can be recorded onto
rECordEr 2.
3.
operate the recorder connected rECordEr 2
to record the playback sound.
4.
The program source can be monitored through
the speakers.
NOTE:
• Yo u c a n c o p y b e t w e e n t w o r e c o r d e r s
(rECordEr 1 and rECordEr 2) vice versa.
ENGLISH
A .