Basic Operation; Operation Procedures; Recorder Operation - Marantz PM6003 User Manual

BASIC OPERATION

OPERATION PROCEDURES

q
PHONO PHONO
INPUT SELECTOR INPUT SELECTOR
BASS BASS
STANDBY STANDBY
POWER ON/OFF POWER ON/OFF
PHONES PHONES
Operate each equipment to start play.
TO PLAY AN ANALOG DISC
1.
Set the INPUT SELECTOR switch q to
PHONO.
2.
Play a disc on the turntable.
3.
Adjust the volume with the VOLUME
control w and adjust the tone with the
BASS and TREBLE controls e.
Notes
• Set the VOLUME control to the minimum position
before placing the stylus on the disc or before
replacing the cartridge.
• Do not apply shock or vibration to the turntable
during play, as this may cause the stylus to jump
and the analog disk to be damaged.
• If the turntable is installed too close to the
speakers, the volume may not be able to be
increased to a high level due to howling.
• Do not switch the power OFF while the stylus is
on the disc surface.
w
TUNER TUNER CD CD AUX/DVD AUX/DVD 1 1 RECORDER RECORDER 2 2 MUTE MUTE
VOLUME VOLUME
SOURCE DIRECT SOURCE DIRECT A A SPEAKERS SPEAKERS B B LOUDNESS LOUDNESS
TREBLE TREBLE BALANCE BALANCE
MIN MIN MAX MAX
L L R R
e
TO LISTEN TO FM/AM BROADCASTS
1.
Set the INPUT SELECTOR switch q to
TUNER.
2.
Tune in the desired station on the tuner.
3.
Adjust the volume with the VOLUME
control w and adjust the tone with the
BASS and TREBLE controls e.
TO PLAY A CD
1.
Set the INPUT SELECTOR switch q to CD.
2.
Play a CD on the CD player.
3.
Adjust the volume with the VOLUME
control w and adjust the tone with the
BASS and TREBLE controls e.
TO PLAY A DVD OR COMPONENT
CONNECTED TO AUX/DVD JACKS
The component connected to the AUX/DVD jacks
on the rear panel can be played as follows.
1.
Set the INPUT SELECTOR switch q to
AUX/DVD.
2.
Play the component connected to the
selected input.
3.
Adjust the volume with the VOLUME
control w and adjust the tone with the
BASS and TREBLE controls e.

RECORDER OPERATION

A
PHONO PHONO
INPUT SELECTOR INPUT SELECTOR
BASS BASS
STANDBY STANDBY
POWER ON/OFF POWER ON/OFF
PHONES PHONES
Control used for operating the tape deck.
PLAYBACK
1.
Set the INPUT SELECTOR switch A to
RECORDER 1 (CD-R) or RECORDER 2 (MD/
TAPE).
2.
Play a prerecorded disc or tape on the
recorder.
3.
Adjust the volume with the VOLUME
control B.
4.
Adjust the tone with the BASS and TREBLE
controls C.
RECORDING
The playback sound of a program source component,
such as a turntable, a tuner, or a CD player, can be
recorded on disc or tape as follows.
1.
Set the program source component with
the INPUT SELECTOR switch A.
2.
Play the program source.
3.
Operate the recorder(s) to record the
playback sound on disc(s) or tape(s).
B
TUNER TUNER CD CD AUX/DVD AUX/DVD 1 1 RECORDER RECORDER 2 2 MUTE MUTE
VOLUME VOLUME
SOURCE DIRECT SOURCE DIRECT A A SPEAKERS SPEAKERS B B LOUDNESS LOUDNESS
TREBLE TREBLE BALANCE BALANCE
MIN MIN MAX MAX
L L R R
C
COPYING
You can copy between two recorders connected
to PM6003.
1.
Select the program source RECORDER 1
with the INPUT SELECTOR switch A.
2.
The RECORDER 1 signal can be recorded
onto RECORDER 2.
3.
Operate the recorder connected RECORDER
2 to record the playback sound.
4.
The program source can be monitored
through the speakers.
Note
• You can copy between two recorders (RECORDER
1 and RECORDER 2) vice versa.
ENGLISH
9