Panasonic PT-AT5000E Operating Instructions Manual page 99

Command Control contents
LENS MEMORY
LOAD
GAMMA
ADJUSTMENT
VXX
TRIGGER 1
(OUTPUT)
TRIGGER 2
(OUTPUT)
<Inquiry commands>
Command Control contents
QPW Power status
QIN INPUT signal status
PICTURE MODE
QPM
status
QSH BLANK status
QFZ FREEZE status
OFF TIMER
QOT
status
WAVEFORM
QWM
status
Loads LENS MEMORY.
LMLI0 = +00000 = LENS MEMORY 1
LMLI0 = +00002 = LENS MEMORY 3
LMLI0 = +00004 = LENS MEMORY 5
Sets Y ADJUST. (OUTPUT)
AGOS0 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09)
Sets R ADJUST. (OUTPUT)
AGOS1 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09)
Sets G ADJUST. (OUTPUT)
AGOS2 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09)
Sets B ADJUST. (OUTPUT)
AGOS3 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09)
Sets GAMMA ADJUSTMENT. (INPUT)
AGIS0 = p1p2d1d2d3
p1p2 = POINT (01 - 09)
Switches TRIGGER 1 (OUTPUT) when RS-232C COMMAND LINK is set in the TRIGGER 1
SETTING menu.
TROI0 = +00000 = LOW
Switches TRIGGER 2 (OUTPUT) when RS-232C COMMAND LINK is set in the TRIGGER 2
SETTING menu.
TROI1 = +00000 = LOW
000 = OFF
CP1 = COMPONENT IN SVD = S-VIDEO IN
VID = VIDEO IN HD1 = HDMI 1 IN HD2 = HDMI 2 IN HD3 = HDMI 3 IN
RG1 = COMPUTER IN
NOR = NORMAL DYN = DYNAMIC 709 = REC709 DCN = D-CINEMA
CN1 = CINEMA1 CN2 = CINEMA2 GM1 = GAME (
0 = OFF
0 = OFF
0 = OFF 1 = 60MIN. 2 = 90MIN. 3 = 120MIN. 4 = 150MIN.
5 = 180MIN. 6 = 210MIN. 7 = 240MIN. (
Parameter
0 = OFF 1 = FULL SCAN(Y) 2 = FULL SCAN(R) 3 = FULL SCAN(G)
4 = FULL SCAN(B) 5 = SINGLE LINE SCAN(Y) 6 = SINGLE LINE SCAN(R)
7 = SINGLE LINE SCAN(G) 8 = SINGLE LINE SCAN(B)
Technical information
Remarks
LMLI0 = +00001 = LENS MEMORY 2
LMLI0 = +00003 = LENS MEMORY 4
LMLI0 = +00005 = LENS MEMORY 6
d1d2d3d4 = OUTPUT (0000 - 0255)
d1d2d3d4 = OUTPUT (0000 - 0255)
d1d2d3d4 = OUTPUT (0000 - 0255)
d1d2d3d4 = OUTPUT (0000 - 0255)
d1d2d3 = INPUT (001 - 099)
TROI0 = +00001 = HIGH
TROI1 = +00001 = HIGH
Parameter
001 = ON

page 40)

1 = ON ( page 79)

1 = ON ( page 79)

page 76)
ENGLISH - 99