Download  Print this page

Before Starting; Cabinet Construction - Kenmore 79041093100 Installation Instructions Manual

30" dual fuel slide-in range
Hide thumbs

Advertisement

Before Starting
Tools you will need
For leveling
legs and anfl-tip
brackets:
_-._
_"_,_i-\,
• Adjustable
wrench or channel
lock pliers
....... _ s_ ....
• 5/16"
Nutdriver
or Flat Head Screw Driver
• Electric
Drill & 1/8 Diameter
_
Drill Bit (5/32"
Masonry
Drill
Bit if installing
in concrete)
• Level & Measuring
Tape
For gas supply connection:
• Pipe Wrench
i_
• Brush
For burner
flame
adjustment:
• Phillips
head
_
and blade-type
_o
screwdrivers
For gas conversion
(LP/Propane
or Natural):
• Open
end wrench
- 1/2"
_
Additional
materials
you will
need: _
• Gas line shut-off valve
• Pipe joint sealant
that
resists action
of LP/_'---PfM_
Propane
gas
.............
• A new flexible
metal
appliance
conduit
(_,,_" NPT x 3/4" or _,,_" I.D.) must be design
certified
by CSA International.
Because
solid pipe
restricts
moving
the range
we
recommend
using a new flexible
conduit
(4 feet
length)
for each new installation
and additional
reinstallations.
• Always
use the (2) new flare
union
adapters
_,'_" NPT x 3/4" or _,_" I.D.) supplied with the
new flexible
appliance
conduit
for connection
of the
range.
Cabinet
Construction
_
To eliminate
the risk of cabinet
burns
and fire, do not have cabinet
storage
space
above the
range.
If there is cabinet
storage
space
above range,
reduce
risk by installing a range
hood that
projects
horizontally
a minimum
of 5" (12.7cm)
beyond
the
bottom
of the cabinet.
|
Caunferfop
Preparation
(figure
1)
° The cooktop
sides of the range
fit over the cutout
edge of your countertop.
° If you have a square
finish [fiat) countertop,
no
countertop
preparation
is required.
Cooktop
sides lay
directly
on edge of countertop.
° Formed
front-edged
countertops
must have molded
edge shaved fiat 3/4"
(1.9 cm) from each front corner
of opening
(Figure
I).
° Tile countertops
may need trim cut back 3/4"(1.9
cm) from each front
corner and/or
rounded
edge
flattened
[Figure
1).
3I_/2".._
(81 cm)
Formed
or tile countertop
trimmed
¾"
(1.9 cm) back
at front
corners
of countertop opening.
Figure
1
If the existing
cutout width
is greater
than
30-1/16"
(76,4 cm), reduce
the 3¼" (1.9 cm) dimension.
Countertop
must be level. Place a level on the
countertop,
first side to side, then front to back.
If the
countertop
is not level, the range
wiii not be level.
The oven must be level for satisfactory
baking
results.
Cooktop
sides of range
fit over edges of countertop
opening.
Gas Entry
Preparation
° The hatched
areas are the locations
where the gas
line can enter the cabinet
[figure
2).
° The recommended
position
for the gas entry line is
located
at 41/_ '' from the left cabinet
wall and 3"
from the floor
[figure
2).
° The wall
shaded
area is the location
where the
electric
junction
box can be installed [read
section
4).
ii iii_ii
Recommended
gas
llne entry
posfflons
//
/
/
/
Note: All dimensions are in inches.
Figure 2
.....
_i!ii
\
\
\
\
\, i

Advertisement

loading

  Related Manuals for Kenmore 79041093100

This manual is also suitable for:

79041103100