Table of Contents
Advertisement
Available languages
Available languages
This appliance
is manufactured
with the frame
grounded
by connection
of a
grounding
strap between
the neutral
power supply
terminal
and the frame.
If used in USA, in a new
branch circuit
installation
(1996 NEC), mobile home
or recreational
vehlcule,
where
local code do not
permit
grounding
through
neutral
(white)
wire
or in Canada;
remove
the grounding
strap from
the frame
and cut the other end, near the neutral
terminal.
Connect the appliance
in usual manner.
Terminal
Block
wire
Silver colored
Terminal
wi re
Electrical Shock Hazard
• Electrlcal ground is required
on this appliance.
• Do not connect
to the electrical
supply
until
appliance
is permanently
grounded.
• Disconnect power to the circuit breaker
or fuse
box before making
the electrical
connection.
• This
appllance
must
be connected
to
a
grounded,
metallic,
permanent
wiring
system,
or a grounding
connector should
be connected
to the grounding
terrnlnal
or wire
lead on the
appffance.
Failure
to do any of the above could resuff in a
fire, personal injury or electrical
shock.
Electrical
Connection
to the Range
This appliance
is manufactured
with
the neutral
terminal
connected
to the frame.
Three Conductor
Wire Connection
to Range
If local
codes
permit
connection
of the frame
grounding
conductor
to the neutral
wire
of the copper
power
supply
cord
(see
Fig. 5):
1. Remove
the 3 screws
at the lower
end
of the
rear
wire
cover,
then
bend
the
lower
end
of the
rear
wire
cover
(access
cover)
upward
to expose
range
terminal
connection
block
(see
Fig. 4).
2. Using
the nuts
supplied
in the
literature
package,
connect
the
neutral
of copper
power
supply
cord
to the
center
silver-colored
terminal
of the terminal
block,
and
connect
the
other
wires
to the outer
terminals.
Match
wires
and
terminals
by
color
(red
wires
connected
to the
right
terminal,
black
wires
connected
to the Jeff terminal)
(see
Fig. 5).
3. Lower
the terminal
cover
and
replace
the 3 screws.
1-1/8"
Dia.
A strainrelief--
Direct
supplied
by the user
Connection
must be installed
at
To 240 V
Hole.
Punch
this location
receptacle
out knockout
for 1-3/8"
Dia.
Figure 5
Cord KitHole
Four Conductor
Wire Connection
to Range
Where
local
codes
does
NOT
permit
connection
of the
frame
grounding
conductor
to the neutral
wire
of the
copper
power
supply
cord
(see
Fig. 6)
1. Remove
the 3 screws
at the lower
end of the
rear
wire
coveb
then
raise
the lower
end
of the
rear
wire
cover
(access
cover)
upward
to expose
range
terminal
connection
block
(see
Fig. 4).
2. Remove
the ground
strap
from
the terminal
block
and
from
the
appliance
frame.
3. Using
the
nuts supplied
in the literature
package,
connect
the ground
wire
(green)
of copper
power
supply
cord
to the frame
of the appliance
with
the
ground
screw,
using
the
hole
in the
frame
where
the
ground
strap
was
removed
(see
Fig. 6).
4.Connect
the neutral
of the
copper
power
supply
cord
to the center
silver-colored
terminal
of the terminal
block,
and
connect
the other
wires
to the outer
terminals.
Match
wires
and
terminals
by color
(red
wires
connected
to the
right
terminal,
black
wires
connected
to the left
terminal).
5. Lower
the terminal
cover
and
replace
the 3 screws.
Btock
Colored
]
Terminal
Wire
7
1-1/8"
Direct
Connection
Hole.
Punch
out
knockout
for
1-3/8"
Dia.
Cord Kit Hol{
A strainretief
supplied
by the user
must be installed at
this location
240 V receptacle
NOTE:
Be sure
to remove
the supplied
grounding
strap
Figure
6
Advertisement
Table of Contents
