Download  Print this page

Check Operation - Kenmore 79041093100 Installation Instructions Manual

30" dual fuel slide-in range
Hide thumbs

Advertisement

Check Operation
Refer to the Use and Care Guide
packaged
with the
range
for operating
instructions
and for care and
cleaning
of your range.
Remove
all
packaging
from
the oven
before
testing.
_[_
install Burner
Bases and Burner Caps
This range is equipped
with sealed
burners
as
shown
(see Figure 14).
a. Unpack
burner
bases and
burner caps.
b. Place burner
bases over
each gas opening.
c. Make
sure the burner
is properly
aligned
and
leveled.
Place burner
caps
over appropriate
burner
bases.
NOTE:
There are no burner
adjustments
necessary
on this
range.
J
Electrode
Figure 14
Turn an Electrical Power and Open Main
Shutoff Gas Valve
Check
the
igniters
Operation
of electric
igniters should
be checked
after
range
and supply
line connectors
have been carefully
checked
for leaks, and range
has been connected
to
electric
power. To check for proper
lighting:
a.Push in and turn a surface
burner
knob to the LITE
position.
You will hear the igniter sparking.
b. The surface
burner
should
light when gas is available
to the top burner.
Each burner
should
light within
four
(4) seconds after
air has been purged
from supply
lines. Visually
check that
burner
has lit.
c. Once the burner
lights, the control
knob should
be
rotated
out of the LITE position.
There are separate
ignition
devices
for each burner.
Try
each knob separately
until all burner
valves have been
checked.
.
the slotted
screw inside. Flame size can be increased
or decreased
with the turn of the screw.
Adjust
flame
until you can quickly
turn knob from HI to
LOWEST
POSITION
without
extinguishing
the flame.
Flame should be as small as possible
and stable
without
going
out.
Repeat the steps from 1 to 4 until all the burners
operate
properJ .
Hollow
Valve
Stem
Figure 15
Adjust
the "LOW"
Setting
of the Dual
Valve
(Fig. 16)
Note: On the dual valve the low setting of each portion
should be adjusted
individually.
a. Push in and turn control
to LITE until the rear portion
of the bridge
burner
ignites only.
b. Qulcklv
turn knob to LOWEST
POSITION.
c. If burner goes out, reset control
to OFF.
d. Remove the surface
burner
control
knob.
e. The rear portion
of the bridge
burner
flame
size can
be increased
or decreased
with the turn of the screw
A. Use screw B to adjust
the flame
size of the center
portion
of the bridge
burner. Turn counterclockwise
the screw to increase
flame
size. Turn clockwise
the
screw to decrease
flame
size. Adjust
flame
until
you can quickly
turn knob from LITE to LOWEST
POSITION
without
extinguishing
the flame.
Flame
should
be as small as possible
without
going
out.
Note:
Air mixture
adjustment
is not required
on surface
burners.
Adjust
the "LOW"
Setting
of Surface
Burner
Valves
(linear
flow
and
three
position
valves)
(Fig
15)
Adjust "LO" setting as follows:
1.
Let appliance
cool down to room temperature.
2.
Light up all burners by turning
each control
knob to
LITE until all burners ignite and set them at HI.
3.
Quickly
turn down the burner involved from HI to
LOWEST SETTING.
4.
If burner goes out, readjust
valve as follows:
Remove the burner control
knob, insert a thin-blade
screwdriver
into the hollow valve stem and engage
: \}
Figure 16
12

Advertisement

loading

  Related Manuals for Kenmore 79041093100

This manual is also suitable for:

79041103100