Table of Contents
Advertisement
Before Starting
Tools You Will Need
For leveling
legs and Anti-Tip
Bracket:
•
Adjustable
wrench or channel lock pliers
5/16'
Nutdriver
or Flat Head Screw Driver
Electric Drill & 1/8" Diameter
Drill Bit (5/32" Masonry
Drill Bit if installing in concrete)
For gas supply connection:
•
Pipe wrench
,<v
For burner
flame
adjustment:
•
Phillips head _
and
blade-type
screwdrivers
For gas conversion
(LP/Propane
or Natural):
Open end wrench - 1/2"
Additional
Materials
You Will Need
Gas line shut-off valve I_
Pipe joint sealant that resists action of LP/Propane gas
A new flexible metal appliance
conduit
(112" NPT x 3/
4" or
1/2'
I.D.)
must
be design
certified
by CSA
International.
Because solid pipe restricts
moving
the
range we recommend
using a new flexible
conduit
(4
to 5 foot length) for each new installation
and additional
reinstallations.
Always
use the (2) new flare union
adapters (112' NPT
x 3/4" or 1/2" I.D.) supplied
with
the
new
flexible
appliance
conduit
for connection
of the range.
Normal
Installation
Steps
1.
Anti-Tip
Bracket
Installation
instructions
Important
Safety
Warning
To reduce the risk of tipping of the range, the range must
be secured to the floor by properly installed anti-tip bracket
and screws packed with the range. Failure to install the
anti-tip bracket will allow the range to tip over if excessive
weight is placed on an open door or if a child ctimbs upon
it. Serious injury might result
from spilled hot liquids
or
from the range itself.
If range is ever moved to a different
location,
the anti-tip
brackets
must also be moved and installed
with the range.
Instructions
are provided
for installation in wood or cement
fastened
to either the floor
or wall.
When installed to the
wail, make sure that screws completely
penetrate
dry wall
and are secured
in wood
or metal.
When fastening
to the
floor or wall, be sure that screws do not penetrate
electrical
wiring
or plumbing.
Ao
B,
Locate the Bracket Using the Template-
(Bracket may
be located on either the left or right side of the range.
Use the information
below to locate the bracket
if
template is not available).
Mark the floor or wall where
left or right side of the range will be located.
If rear of
range is against the wall or no further than 1-1/4" from
wall when
installed,
you may use the wall or floor
mount method.
If molding
is installed and does not
allow the bracket to fit flush against the wall, remove
molding or mount bracket to the floor. For wall mount,
locate
the bracket by placing the back edge of the
template
against the rear wall and the side edge of
template on the mark made referencing the side of the
range. Place bracket on top of template
and mark
location of the screw holes in wall.
If rear of range is
further than 1-1/4' from the wall when installed, attach
bracket
to the floor.
For floor mount,
locate the
bracket by placing back edge of the template
where
the rear of the range will be located.
Mark the location
of the screw holes, shown in template.
Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot
hole where screws are to be located.
If bracket is to be
mounted to the wall, drill pilot hole at an approximate
20 ° downward
angle. If bracket is to be mounted
to
masonry
or ceramic floors, drill a 5/32" pilot hole 1-3/
4" deep. The screws provided
may be used in wood or
concrete
material.
Use a 5/16' nut-driver
or flat head
screwdriver
to secure the bracket
in place.
FASTEN BRACKET (WALL O RFLOOn M OUNTnNG)
-,-._i
14.--1-1/4" Max.
Leveling Leg _7_]
h
FASTEN BRACKET (_oo_ MOUNTING O NLY)
Leveling Leg --
Floor Mount
J_i
Bracket
Advertisement
Table of Contents
