Advertisement
Available languages
Available languages
Washer/Dryer
Dimensions
71%"
(1819 mm)
Explosion
Hazard
Keep flammable
materials
and vapors, such as
gasoline,
away from dryer.
FaiJure to do so can result in death, explosion,
or fire.
You will need
[]
A location that allows for proper exhaust installation. See
"Venting Requirements."
[]
[]
[]
[]
[]
[]
A separate 30-amp circuit.
If you are using a power supply cord, a grounded electrical
outlet located within 2 ft (610 mm) of either side of the washer/
dryer. See "Electrical Requirements."
A sturdy floor to support the washer/dryer
weight (washer/
dryer, water, and load) of 500 Ibs (226.8 kg).
A level floor with a maximum slope of 1" (25 mm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
A water heater set to deliver 120°F (49°C) water to the washer.
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
The washer/dryer
must not be installed or stored in an area where
it will be exposed to water and/or weather.
Do not operate your washer in temperatures
at or below 32°F
(0°C). Some water can remain in the washer and can cause
damage in low temperatures.
See "Washer/Dryer Care" in the
Washer/Dryer User Instructions for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures,
the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile homes,
or sleeping quarters. Contact your local building inspector.
Installation
Clearances
The location must be large enough to allow the dryer door to open
fully.
27"
(686
mm)
*Most installations require a minimum 5" (127 mm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
Installation
spacing
for recessed area or closet
installation
The following spacing dimensions are recommended
for this
washer/dryer. This washer/dryer
has been tested for spacing of 0"
(0 mm) clearance on the sides. Recommended
spacing should be
considered for the following reasons:
[]
Additional spacing should be considered for ease of
installation and servicing.
[]
[]
[]
Additional clearances might be required for wall, door,
and floor moldings.
Additional spacing on all sides of the washer/dryer
is
recommended
to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
O
oooO
I1
I
m
_i
27' il 1"
(25 rnm) (686 inn])
(25 mn])
A
I1 II
÷1
31"_Z;-_2,,
I
1"*
_6"
(152inn])
48 il. 2 -
(310cn]2)
1
J 31_
-_(76 rnm)
|
24in.2-
2[ 3"
(155cm2)
(76n]m)
5"**
(25mn])(813n]rn)(127 mm)
B
C
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
*Required spacing
**Rear clearance may be 1" (25 mm) when house exhaust system
is lined up directly with dryer exhaust.
Mobile Home = Additional
installation
Requirements
This washer/dryer
is suitable for mobile home installations.
The installation must conform to the Manufactured
Home
Construction
and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280) or the Canadian Manufactured
Home Standard, CAN/CSA-Z240
MH.
Advertisement
