Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Cooper Security i-on16
Summary of Contents for Cooper Security i-on16
- Page 1 Security System User Guide...
-
Page 2: Table Of Contents
Contents 1. Introduction ............ 1 Controls and Displays.......... 3 Displays............3 Controls:............4 2. Everyday Operation ......... 5 Access to the System .......... 5 Entering and Leaving the Protected Area .... 5 Setting.............. 6 Full Set ............6 Quick Set ............8 Part Set ............ -
Page 3: Introduction
The i-on16 is a wireless intruder alarm system intended mainly for use in domestic and small commercial properties. The heart of the i-on16 system is the control unit and its keypad. The control unit contains the main wireless receiver, the power supply and stand-by battery. - Page 4 7. Smoke Detector. 8. Passive Infra Red. 9. External siren/strobe. Figure 1. i-on16 Peripherals A complete i-on16 system comprises a control unit and up to: 16 fixed wireless alarm detectors One external siren/strobe unit 16 portable four button remote controls 16 portable panic alarm buttons 16 users.
-
Page 5: Controls And Displays
This rest of this guide shows the simple procedures required to operate and administer the system. For information on installing the i-on16 please read i-on16 Installation and Programming Guide. Each of the radio peripherals also have their own guides. Controls and Displays Figure 2 shows the controls and displays available on the keypad. -
Page 6: Controls
Introduction To draw your attention to special events the rim of the navigation key glows red. The four LEDs on the right of the programming keys show you that the system is set or unset. The left hand LED glows when the system is full set, the second from left glows when the system is part set. -
Page 7: Everyday Operation
15). This user’s default access code is “1234”, and they do not have any tag or other device registered to their account. Cooper Security Limited recommend that you change the default access code as soon as possible (see page 16). -
Page 8: Setting
Everyday Operation Setting Note: Whenever you set the system you should first make sure that all doors and windows are secure. Full Set When the system is full set, all the detectors intended to detect intruders are primed, ready to raise an alarm. (If you want to protect just part of your premises use “part set”, see page 8 .) Make sure the system is idle. - Page 9 Everyday Operation At the end of the exit time the exit warning tone stops and you should hear a double “beep” confirmation tone to let you know that the system is set. The display shows the System Set message "System Set" for a few seconds, followed by the standby screen.
-
Page 10: Quick Set
Everyday Operation Quick Set Quick Setting does not require the use of an access code or tag. (The Installer must enable this facility for you.) Make sure the system is idle. Press A. Setting:Full Set 10 to set The keypad gives the exit warning tone. -
Page 11: If The System Will Not Set
Everyday Operation If the System Will Not Set Normally, the system will set only when all the detectors are “quiet”, that is: not reporting any activity. (This does not apply to those detectors on your exit door or exit/entry route. The system expects these detectors to be active as you leave the protected area.) If you try to set when one or more detectors are still active then... -
Page 12: Setting With A Remote Control
Everyday Operation Setting With a Remote control Note: You must program the control unit to recognise ("learn") a remote control, see page 23. Secure all your windows and doors. Make sure the system is idle, and that you can hear the warning tones from the keypad. -
Page 13: Unsetting
Everyday Operation Unsetting When unsetting the system do not stray from the entry route designated by the installer. If you do then you will cause an alarm. Enter by the designated entry door. The control unit starts the entry tone. EITHER Key in your access code. -
Page 14: Alarms
3. Alarms Types of Alarm The i-on16 normally starts an alarm when it receives an alarm signal from one of its detectors. In addition, you can start a panic alarm from the keypad. The table below shows the different kinds of alarms possible. -
Page 15: Silencing An Alarm
Alarms Silencing an Alarm In an alarm the i-on16 operates the siren. The siren runs for a limited time set by the installer (a maximum 15 minutes for intruder and PA alarms). If you return to the control unit after the siren has stopped and key in your access code then the red LEDs around the navigation keys glow to tell you that an alarm has occurred. -
Page 16: Alerts (Or Why Is It Beeping?)
4. Alerts (or Why is it Beeping?) From time to time the control unit may detect that there is a problem with the system. It will try to inform you of this by starting an alert. During an alert the rim of the navigation pad glows red, and the keypad will give an short “beep”... -
Page 17: Administration
5. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what type of user you are: Admin User or Normal User. An Admin User has access to all the options of the Menu. A Normal User: Can change their own access code. -
Page 18: Omit Zones
Administration Omit Zones You may wish to prevent a zone causing an alarm. For example, if your garage door is protected by a detector, but you wish to leave it unlocked for the delivery of a parcel, you may wish to omit that detector when you set the rest of the alarm system. -
Page 19: Name
Administration Press u or n to display the user you wish to edit, and then press >. The bottom line shows one of a list of the options that you can edit: Name Type (this option is not available for User 01) Code Prox Tag Remotes... -
Page 20: User Types
Administration 2 abc 3 def A B C Æ Å Ä D E F 4 ghi 5 jkl 6 mno J K L M N O Ø Ö G H I 7 pqrs 8 tuv 9 wxyz P Q R S T U V W X Y Z Space 0... -
Page 21: Proximity Tags
Administration Proximity Tags A proximity tag is a small plastic token with a low powered radio transmitter inside. Each tag contains a unique identity code. Inside the keypad is a sensor. When you present the tag within about 10mm of the front of the keypad, the control unit senses the presence of the tag and reads its identity code. -
Page 22: Remote Controls
Administration Remote controls A remote control is a transmitter that you can attach to a keyring. The remote control has four buttons and a small LED that glows when it transmits a signal. When delivered from the factory three of the buttons are dedicated to setting or unsetting the system (see Figure 4). - Page 23 Administration If you do not wish to register a remote control press X. If the control unit has already learned that remote control then you will hear a low tone and the display tells you that the remote control is already in use. If you have a remote control and want to know who it belongs to then use the Test - Remotes menu option, see page 24 .
-
Page 24: Adding Users
Administration unauthorised person can use it. Also, if you wish to reassign a device to another user, you must first delete it from the system. Enter the Menu and select Users - Edit User. The bottom line of the display shows the first in a list of the users currently recognised by the system. -
Page 25: Deleting Users
Administration The display asks you to assign a new user code. Key in the user code you want the new user to employ. Key it in a second time when prompted by the display. The display asks you to present a proximity tag to the keypad. -
Page 26: View Log
Administration Once you delete a user, the system does not respond to their access code or to their proximity tag. In addition, the control unit "forgets" the identity of all remote controls and PAs assigned to the user. View Log The control unit keeps a log of the last 250 events (for example, alarms and setting/unsetting events). -
Page 27: System Configuration
Administration Siren Press > to turn the siren on and off again. The word "On" or "Off" on the display shows whether you should be hearing the siren. Keypad Press each key once. The display shows a character in response. Press both PA keys together to test. -
Page 28: Facilities On/Off
Administration The bottom line of the display shows the first item of the System Configuration menu. Press u or n to scroll through the options available, followed by > to gain access to an option. Facilities On/Off Chime The installer may have set up your alarm system to give a chime tone whenever something triggers one or more detectors while the system is unset. -
Page 29: Loudspeaker Volume
Administration Note: The internal clock does not adjust itself for daylight saving. Loudspeaker Volume You can make the tones from the internal loudspeaker louder or softer: Enter the Menu and select System Config - Loudspeaker. Loudspeaker The top line of the display [**** shows “Loudspeaker”... - Page 30 Administration Key in the new telephone number from the keypad. If necessary, press u to move the cursor left, or n to move the cursor to the right. Press < to remove digits to the left of the cursor. Press Y to store the changes you have made. Page 28...
-
Page 31: List Of Menu Options
List of Menu Options Item Page Omit Zones (Zone 01, 02, …) Users Edit User (for each user:) Name Type (not U01) Code Prox Tag Remote Panic Alarm Add User Delete User View Log Test Siren Keypad Walk test Remotes Panic Alarms Prox Tags System Config... - Page 32 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book.