Cooper Security i-ON 40 Installation Manual
  1. Manuals
  2. Brands
  3. Cooper Security Manuals
  4. Security System
  5. i-On 40
  6. Installation manual

Cooper Security i-ON 40 Installation Manual

Hide thumbs Also See for i-ON 40:
Table of Contents

Advertisement

Quick Links

See also: Administrator's Manual , User Manual
Security System
Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the i-ON 40 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cooper Security i-ON 40

Summary of Contents for Cooper Security i-ON 40

  • Page 1 Security System Installation Guide...
  • Page 2 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice.

  • Page 3: Table Of Contents

    CONTENTS Outputs ..........23 Fuses ..........23 Electrical Safety ......... 23 1. Introduction........1 Compliance Statements....... 23 Communications....... 1 Compatible Equipment ......24 Level Setting or Partitioned System..1 2. Before You Begin......2 Preparation ......... 2 Siting the Unit........2 Guided Tour ........
  • Page 4 i-on40 This page is intentionally blank. Page iv...

  • Page 5: Introduction

    i-on40 8750 An Ethernet module that allows 1. Introduction alarm reporting and remote maintenance over the internet. The i-on40 is the control unit for a hybrid 8844 A GPRS module that allows wired/wirefree alarm system intended for internet protocol access over the domestic and light commercial use.

  • Page 6: Before You Begin

    To do this you should conduct signal strength tests. Cooper Security produce the Scantronic 790r hand held signal strength meter for this purpose. Alternatively, you can power the control unit from a battery...

  • Page 7: End Station Pcb

    i-on40 10. Siren test output (not used in UK). 5. Printed circuit board (PCB). 6. Cable entry holes for detector and keypad Keypad Controls and Displays wiring. 7. Transformer. 8. Mains connector block. 9. Cable entry hole for mains. 10. Back Tamper switch (if fitted). End Station PCB 2 abc 3 def...

  • Page 8: Power Availability

    i-on40 Power Availability Before connecting any external devices to the control unit, you must make sure that the control unit can provide sufficient current to power the system during a mains failure for the time required to meet Grade 2 PD6662 or EN50131-1. The amount of current available from the control unit depends on the battery fitted.

  • Page 9: Installation

    Figure 9 Fixing Holes and Cable Entries Figure 10 Screw Keypad Back Box to Wall 1. Fixing holes. 2. Cable entries. Cooper Security recommend that you use at least four fixing holes when mounting Page 5...

  • Page 10: Connecting Keypads To End Station

    i-on40 Star Daisy Chain Connecting Keypads to End Station Cable Type In general, the control unit requires standard 7/0.2 un-screened four core alarm cable for wiring to keypads. terminate For maximum performance in harsh environments use twisted pair cable with a MENU 2 abc 3 def...

  • Page 11: Keypad Addressing

    i-on40 control unit and 5 in Fig 8 for the keypad). ABCD-ON Fitting a jumper to the pins adds a MENU termination to the cable. 2 abc 3 def 4 ghi 5 jkl 6 mno 7 pqrs 8 tuv 9 wxyz In a daisy chain configuration terminate each end of the chain (see Fig 11 ).

  • Page 12: Mains Cabling

    i-on40 Mains Cabling Step 4. Connect Wired Make sure that the mains supply cable does Zones not run vertically behind the aerials within the end station case. Four Wire Closed Circuit Connections If you wish run mains cable through the side of the case, make sure that they are horizontal for the last metre before entering the case.

  • Page 13: Step 5. Connect Wired Peripherals

    i-on40 Step 5. Connect Wired Peripherals 100 Ohms 12V + Tamper In Tamper Out Strobe +ve Strobe -ve Alarm contacts Trigger -ve 2K2 EOL Zone 2 Tamper contacts Zone 1 Alarm contacts 2K2 EOL Tamper contacts Alarm contacts Alarm contacts Zone 1 2K2 EOL Tamper contacts...

  • Page 14: Step 6. Fit A Plug-By Communicator

    i-on40 Step 6. Fit a Plug-By If the system has already been installed: 4. Re-connect the battery. Communicator 5. Fit the case lid. The control unit can be connected to a 6. Apply mains power. separate communicator or speech dialler 7.

  • Page 15: Programming Before Installation

    i-on40 Note: Connecting the battery without mains From this point on, the display operates power will not start the system. (See in the selected language. If you want to “Programming A Control Unit Before change the language later use Installer Installation”...

  • Page 16: Step 9. Commission The System

    i-on40 Step 9. Commission the System After installing the control unit you should commission the alarm system as follows: 1. Use the Installer Menu (see Chapter 4) to teach the control unit the identity of its radio detectors and any other peripherals.

  • Page 17: Programming

    i-on40 Leaving the Installer 4. Programming Menu This section is summary of the Installer If you wish to leave the Installer Menu at Menu on the i-on40. Please see the i-on40 any time. Programming Reference for a more detailed description. 1.

  • Page 18: Restoring Factory Defaults

    i-on40 3. Identify the Reset Codes pins on the 4. Press u or n to display the desired main PCB (see Figure 3). wiring type on the bottom line of the display and then press Y to select it. 4. Short the Reset Codes pins together using a screwdriver or jumper link.

  • Page 19: Installer Menu

    i-on40 Installer Menu 1 DETECTORS/DEVICES 2 OUTPUTS 3 SETTING OPTIONS 4 SYSTEM OPTIONS Detectors Radio outputs Full Set Wired Zone type Add/Del Detectors Add Outputs Name User Access Zone 17...40 Edit Outputs Exit Mode PA keys active Delete all Output 01...08 Quick Set Part Set B Edit Zones...

  • Page 20: Zone Types & Attributes

    i-on40 Zone Types & Attributes alarm occurs until the entry/exit timer expires. Note: If you give an Entry Route zone one (Hint: You can select a zone type quickly by of the Part Set attributes then you can keying the number shown in brackets after program that zone to behave like a Final the type’s name, for example:“05”...
  • Page 21 i-on40 Notes: External PSU Low Volts (13). 1. The keyswitch zone types are intended Use this zone type to monitor the Low for use on zones that connect to an access Battery output of an external power control keypad, electronic key or other type supply unit.

  • Page 22: Output Types

    i-on40 control unit also lights the red LEDs Force Set Omit around the navigation key on the When this attribute is set to Yes a keypad to alert the user. user with a remote control can set the You can apply the soak test attribute system while the zone is open to Normal Alarm, Entry Route and (active).
  • Page 23 i-on40 Type: Active when: Type: Active when: There is a supervision failure the output when the zone has Supervision on any radio zone. The output been restored and a user has (09) remains active until all acknowledges the fault by supervision failures are reset.
  • Page 24 i-on40 Type: Active when: Type: Active when: operate if the exit mode is Part Set B Setting Part Set B. silent set or instant set. (35) Deactivated on unsetting Part Set B. (Available only in a Part Armed (24) The system is full or part set. Setting system) PIR Set The system is set.

  • Page 25: Exit Modes

    i-on40 Exit Modes 7. Maintenance When choosing an exit mode for a partition The control unit should be inspected once or a part set, the available options are: per year. At each inspection: Final Door Use this option to complete Check the control unit for obvious signs setting the system by closing a of damage to the case or its lid.

  • Page 26: Technical Specification

    Blocked for 90s after 10 Product 40 zone hybrid endstation incorrect codes in series. Description with remote keypads. Proximity tag 4,294,967,296 (2 Manufacturer Cooper Security Ltd. differs Environmental Class II. Radio Operating Tested -10 to +55°C. temperature Radio Section Operating frequency...

  • Page 27: Electromagnetic Compatibility

    i-on40 Monitoring Mains fail, battery low includes voltage, battery failure. Electromagnetic Compatibility Immunity Conforms to EN50130-4. Emissions Conforms to EN61000-6-3. Outputs O/P 1 - 2 Voltage free, single pole relay contacts rated 24VDC @ 1A. O/P 3 - 4 Open collector transistor, +12VDC when inactive, 0V when active.
  • Page 28 i-on40 Compatible Equipment 703rEUR-00 Multi-function transmitter 770rEUR-00 Wireless Accessory Module 706rEUR-00 Two button PA/tilt switch transmitter 771rEUR-00 Info Module 710rEUR-00 Two button PA 08844EUR-00 GPRS module 713rEUR-00 Pet tolerant PIR 08750EUR-00 Ethernet module 714rEUR-00 PIR Transmitter (Small 9040UK-00 Speaker boxed case) i-fb01 Four button remote...

Table of Contents