Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H8232
Summary of Contents for Grizzly H8232
- Page 1 3-PIECE FRAMING/FINISH/PALM NAILER KIT OWNER'S MANUAL COPYRIGHT © SEPTEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TS9957 PRINTED IN CHINA...
- Page 2 ���� ������ �������� �������� ������ ������������ �� ��� ������ ������ ���������� ����������� ��� ������� �� ���� ������������������ ������� �� ����� ���������� ��� ������ ��� ������������ ����� �� ���� ������ ��� ������ �� ������� �������� ������� ��������� ����������� ������������� �� ������ ���...
-
Page 3: Safety Instructions For Pneumatic Tools
Keep work area well lighted. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. - Page 4 24. BE AWARE OF HOSE LOCATION WHEN RISK TOOLS. Hoses can easily become a tripping hazard when laid across the floor or spread out in a disorganized fashion. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit TOOLS before RECOMMENDED recommended ALLOW UNTRAINED...
-
Page 5: Additional Safety Instructions For Nailers
5. CHECK VALVE: Do not use a check valve or any other fitting that allows air to remain in the tool. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit 6. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. - Page 6 Use this and other tools with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit...
-
Page 7: Tool Data
Foreword The specifications, details, and photo- graphs in this manual represent the Model H8232 as supplied when the manual was prepared. However, owing to Grizzly’s pol- icy of continuous improvement, changes may be made at any time with no obliga- tion on the part of Grizzly. - Page 8 D. Hex Wrenches 3, 4, 5, 6mm ... 1 Each E. Safety Goggles ... 1 F. Carrying Case ... 1 G. Leather Palm Nailer Pouch ... 1 H. Tool Oil Bottle ... 1 Figure 1. Model H8232 inventory. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit Inventory...
-
Page 9: Compressed Air System
Compressed Air System The Model H8232 is designed to be oper- ated at the following air pressures using clean, dry, regulated, compressed air: Nailer Operating Air Pressure Framing ... 80–110 PSI Finish ... 60–100 PSI Palm ... 70–100 PSI DO NOT exceed the 120 PSI maximum operating pressure for your nailer. - Page 10 Serious injury may occur. DO NOT attempt to modify or bypass the safety nose mechanism to make the framing/finish nailer fire without pushing the safety nose down. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit...
- Page 11 Figure 3. Sliding magazine pusher back and engaging catch lever. 3. Insert a strip of nails, pointed-end down, into the magazine as shown in Figure 4. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit OPERATIONS " Shank Diameter ⁄ " Figure 4. Loading nails into the magazine.
- Page 12 — If the nail drove into the wood far enough, continue with your intended operations. — If the nail either went too far or not far enough, then go to the Adjusting Nail Penetration section on the next page. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit...
- Page 13 2mm or ⁄ ". Model H8232 3-Piece Framing/Finish/Palm Nailer Kit Adjusting Nail Penetration Depending on the type of stock and nails you are using, it may be necessary to adjust the depth of nail penetration for your framing/finish nailer.
-
Page 14: Clearing Jammed Nails
1. DISCONNECT NAILER FROM THE 2. Pull back and latch the magazine push- 3. Open the nailer nose by removing the Model H8232 3-Piece Framing/Finish/Palm Nailer Kit the nailer safety nose (see Figure 10). Figure 10. Clearing a jammed nail. -
Page 15: Replacing Pistons/O-Rings
O-Ring Repair Kit ... PH8232092 Palm Nailer: Piston Repair Kit ... PH6141026 O-Ring Repair Kit ... PH6141027 Model H8232 3-Piece Framing/Finish/Palm Nailer Kit Always disconnect air from nailer whenever servicing! During mainte- nance, a nailer connected to air may fire accidentally, causing serious per- sonal injury! Framing &... - Page 16 19mm wrench to tighten the nose piece. Note: For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit...
-
Page 17: Cleaning And Lubrication
Ignoring this warning may lead to serious personal injury or even death! Model H8232 3-Piece Framing/Finish/Palm Nailer Kit Lubricating Standard pneumatic tool oil has been included with your new Grizzly nailer to help maintain its useful life. - Page 18 �� �� �� �� �� �� �� �� �� �� �� �� �� �� ���� �� ���� Model H8232 3-Piece Framing/Finish/Palm Nailer Kit �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��...
- Page 19 CAP SCREW M5-.8 X 8 PW02M FLAT WASHER 5MM PH8233049 ADJUSTING NUT PH8233050 SAFETY YOKE PH8233051 SAFETY NOSE Model H8232 3-Piece Framing/Finish/Palm Nailer Kit REF PART # DESCRIPTION PH8233052 COPPER COLLAR PH8233053 SAFETY NOSE CASE PORS060 O-RING 59.5 X 2.0 S60...
- Page 20 Finish Nailer Parts Breakdown Model H8232 3-Piece Framing/Finish/Palm Nailer Kit...
- Page 21 PH6143042 CONNECTOR PH6143043 BRACKET PH6143044 SPECIAL BOLT PH6143045 STEEL BALL 2MM PH6143046 COMPRESSION SPRING PH6143047 SAFETY BRACKET PH6143048 SPECIAL PIN Model H8232 3-Piece Framing/Finish/Palm Nailer Kit REF PART # DESCRIPTION PEC09M E-CLIP 6MM PH6143050 ALIGNMENT PIN PH6143051 NOSE BRACKET PH6143052 ADJUSTMENT NUT...
- Page 22 PH6141016 PH6141017 PH6141018 PH6141019 PH6141020 PH6141021 PH6141022 PH6141023 PW02M PH6141025 PH6141026 PH6141027 PH8232228 Model H8232 3-Piece Framing/Finish/Palm Nailer Kit ��� ��� ��� ��� ��� ��� ��� ��� DESCRIPTION BUMPER 16 X 40 X 8 AXLE SLEEVE 8MM NAILER BODY AIR INLET VALVE 1/4" NPT...
-
Page 23: Troubleshooting
Nailer does not fire. 1. Nailer is not lubricated. 2. Nail is jammed in magazine or 3. Piston shaft is damaged. 4. Air pressure too low. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit are damaged. from moving freely in maga- zine. -
Page 24: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance.