Table of Contents
Advertisement
Quick Links
18 GAUGE FINISH ANGLE NAILER
MODEL H5570
INSTRUCTION MANUAL
COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUS-
TOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES.
PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Advertisement
Table of Contents
Related Manuals for Grizzly H5570
Summary of Contents for Grizzly H5570
-
Page 1: Instruction Manual
INSTRUCTION MANUAL COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. -
Page 2: Safety Instructions For Pneumatic Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. - Page 3 WHILE UNSUPERVISED. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING THE TOOL. Seek formal training or research books or maga- zines that specialize in pneumatic tools. H5570 18 Gauge Finish Angle Nailer RECOMMENDED Consult DAMAGED PARTS. ALLOW UNTRAINED...
- Page 4 DO NOT USE A CHECK VALVE OR OTHER FITTING ALLOWS AIR TO REMAIN IN THE TOOL. H5570 18 Gauge Finish Angle Nailer Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always...
- Page 5 Commentary We are proud to offer the Grizzly Model H5570 18 Gauge Finish Angle Nailer. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commit-...
-
Page 6: Compressed Air System
Compressed Air System The Model H5570 is designed to be oper- ated at 70-100 psi. DO NOT exceed the maximum operating pressure for your model. Before using your new nailer, install the included ⁄ " NPT male quick connect fitting on the nailer and a ⁄... -
Page 7: Operation
As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H4196 in your air line. Figure 1. Lubricating nailer via air inlet. OPERATION Loading Nailer... -
Page 8: Operating Nailer
Depress the safety yoke mechanism on your workpiece. Figure 4. Example of nail deflection. H5570 18 Gauge Finish Angle Nailer Before pressing the trigger, make sure your free hand is positioned out of the way of a potential path of a nail in case of deflection. -
Page 9: Clearing Jammed Nails
Clearing Jammed Nails To clear a jammed nail from the dis- charge area on the Model H5570: Disconnect the nailer from the air supply! Pull the spring loaded pusher all the way back and remove the nail stick. Flip up the quick release latch located on top of the nailer nose assembly as shown in Figure 6. -
Page 10: Replacing Pistons/O-Rings
Remove the rear cap as shown in Figure 8. Figure 8. Removing rear cap. H5570 18 Gauge Finish Angle Nailer The top of the piston should now be visible inside the cylinder, which is housed in the head of the nailer. - Page 11 H5570 PART BREAKDOWN H5570 18 Gauge Finish Angle Nailer...
- Page 12 37A PH5570037A LATCH PH5570038 DRIVER GUIDE COVER PH5570039 39-1 PEC01M E RING 3MM * These items are not shown in the illustration. H5570 18 Gauge Finish Angle Nailer PART # DESCRIPTION PSB33M CAP SCREW M5-.8 X 12 PH5570041 DRIVER GUIDE PSB97M CAP SCREW M5-.8 X 6...
-
Page 13: Troubleshooting
1. Nail is jammed in maga- zine or discharge area. 2. Piston shaft is damaged. 3. Air pressure too low. H5570 18 Gauge Finish Angle Nailer ACTION 1. O-rings must be replaced & operation of safety yoke must be checked. -
Page 14: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. -
Page 15: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 16 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...