Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H7664
Summary of Contents for Grizzly H7664
-
Page 1: Instruction Manual
2-IN-1 COMBINATION NAILER/STAPLER MODEL H7664 INSTRUCTION MANUAL COPYRIGHT © JULY, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL7293 PRINTED IN CHINA... -
Page 3: Table Of Contents
Loading ...12 Operating ...12 Adjusting Depth ...13 Single/Bump Fire Operation ...14 Clearing Jammed Nails/Staples ...14 Replacing Pistons/O-Rings ...15 SECTION 5: MAINTENANCE ...17 Cleaning ...17 Lubricating ...17 Troubleshooting ...18 H7664 Parts Breakdown ...19 H7664 Parts List ...20 WARRANTY AND RETURNS ...21... -
Page 4: Section 1: Safety
USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed. INFLUENCE ALCOHOL. H7664 2-in-1 Combination Nailer/Stapler WORKSHOP CHILD UNDER DRUGS... - Page 5 17. REDUCE UNINTENTIONAL STARTING. Do not carry tool with hand on trig- ger and always disconnect from air when not in use. H7664 2-in-1 Combination Nailer/Stapler 18. DISCONNECT TOOLS before ser- vicing and changing accessories. 19. USE ACCESSORIES. owner’s manual for recommended accessories.
-
Page 6: Additional Safety Instructions For Nailers And Staplers
COMPRESSED AIR RATING: Do not connect the nailer/stapler to compressed air that exceeds 120 PSI. CHECK VALVE: Do not use a check valve or any other fitting that allows air to remain in the tool. H7664 2-in-1 Combination Nailer/Stapler... - Page 7 82 decibels. To protect your hearing, always wear ANSI approved ear protection when operating this nailer/stapler. H7664 2-in-1 Combination Nailer/Stapler Never point this nailer/stapler at your- self or another person! Always pay attention to the direction this nailer/ stapler is pointed.
-
Page 8: Section 2: Introduction
SECTION 2: INTRODUCTION Foreword We are proud to offer the Grizzly Model H7664 2-in-1 Combination Nailer/Stapler. This model is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzly’s commitment to customer satis-... -
Page 9: Section 3: Set Up
SECTION 3: SET UP Unpacking Your Model H7664 left our warehouse in a carefully packed box. If you discover the nailer/stapler is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing mate- rials for possible inspection by the car- rier or its agent. -
Page 10: Compressed Air System
Compressed Air System The Model H7664 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres- sure for your model. Before using your new nailer/stapler, reg- ulate the air pressure on your air compres- sor to the minimum PSI for your model. -
Page 11: Safety Yoke
Serious injury may occur. H7664 2-in-1 Combination Nailer/Stapler 5. Without pressing the trigger, depress the safety yoke mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects. -
Page 12: Section 4: Operations
SECTION 4: OPERATIONS Loading When replacing brads or staples in your Model H7664, follow these guidelines: Gauge: 18 Brad Length: ⁄ "-2" Staple Length: ⁄ "-1 ⁄ " (crown Capacity: 100 To load your nailer/stapler: 1. DISCONNECT NAILER/STAPLER FROM THE AIR SUPPLY! 2. -
Page 13: Adjusting Depth
— If the nail/staple either went too far or not far enough, then go to the Adjusting Depth sub-section on this page. H7664 2-in-1 Combination Nailer/Stapler Adjusting Depth A depth adjustment knob is attached to the nose for setting the nail/staple depth. -
Page 14: Single/Bump Fire Operation
DO NOT use dirty or damaged nails/staples! Push the magazine pusher forward to the front of the magazine until the catch lever locks. H7664 2-in-1 Combination Nailer/Stapler NAILER/... -
Page 15: Replacing Pistons/O-Rings
A replacement piston and O-ring kit, part PH7664084, may be purchased for the Model H7664. Always disconnect air from nailer/ stapler whenever servicing! During maintenance, a nailer/stapler con-... - Page 16 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appro- priate breakdown diagram in the back of this manual for component loca- tions. H7664 2-in-1 Combination Nailer/Stapler...
-
Page 17: Section 5: Maintenance
H7664 2-in-1 Combination Nailer/Stapler Lubricating Pneumatic tool oil has been included with your new Grizzly nailer/stapler to help maintain its useful life. Place two to three drops of oil in the nailer/stapler air inlet (as shown in Figure 8) before every use, or after 2 hours of continuous use. -
Page 18: Troubleshooting
H7664 2-in-1 Combination Nailer/Stapler Solution 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use tef- lon tape. -
Page 19: H7664 Parts Breakdown
� � �� �� �� � � � �� � �� �� �� �� �� �� �� H7664 2-in-1 Combination Nailer/Stapler �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ���... -
Page 20: H7664 Parts List
PH7664076 PH7664077 PH7664078 PH7664079 PLW02M PAW03M PAW04M PH7664083 PH7664084 H7664 2-in-1 Combination Nailer/Stapler DESCRIPTION SAFETY YOKE CAP SCREW M4-.7 X 12 FLAT HD SCR M4-.7 X 6 O-RING 2.4 X 1.8 PUSHER STICK PUSHER PUSHER STICK O-RING 4.5 x 1.2... -
Page 21: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. - Page 22 H7664 2-in-1 Combination Nailer/Stapler...
- Page 23 ____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
- Page 24 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...