Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H6143
Summary of Contents for Grizzly H6143
-
Page 1: Instruction Manual
16 GAUGE FINISH NAILER INSTRUCTION MANUAL COPYRIGHT © AUGUST, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. -
Page 2: Safety Instructions For Pneumatic Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. - Page 3 UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always disconnect from air when not in use. H6143 16 Ga. Finish Nailer 17. DISCONNECT TOOLS before ser- vicing and changing accessories. 18. DO NOT OVERREACH. Keep proper footing and balance at all times.
-
Page 4: Additional Safety Instructions For Nailers
COMPRESSED AIR RATING: Do not connect the nailer to com- pressed air that exceeds 120 PSI. CHECK VALVE: Do not use a check valve or any other fitting that allows air to remain in the tool. H6143 16 Ga. Finish Nailer... - Page 5 85-90 decibels. To protect your hear- ing, always wear ANSI approved ear protection when operating. H6143 16 Ga. Finish Nailer Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed.
-
Page 6: Contact Info
Foreword We are proud to offer the Grizzly Model H6143 16 Ga. Finish Nailer. This model is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-... - Page 7 Unpacking Your Model H6143 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing mate- rials for possible inspection by the car- rier or its agent.
-
Page 8: Compressed Air System
Compressed Air System The Model H6143 is designed to be oper- ated at 60–100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres- sure for your model. Before using your new nailer, regulate the air pressure on your air compressor to the minimum PSI for your model. - Page 9 Serious injury may occur. H6143 16 Ga. Finish Nailer 5. Without pressing the trigger, depress the safety nose mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects.
- Page 10 Operating connect fitting. the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded. H6143 16 Ga. Finish Nailer...
-
Page 11: Adjusting Depth
— If the nail either went too far or not far enough, then go to the Adjusting Depth section on this page. H6143 16 Ga. Finish Nailer Adjusting Depth A depth adjustment knob is attached to the nose for setting the nail depth. -
Page 12: Clearing Jammed Nails
Throw the damaged nail away and insert a new nail stick that only contains clean, undamaged nails. DO NOT use dirty or damaged nails! Release the catch lever and let the pusher slide to the front of the maga- zine. H6143 16 Ga. Finish Nailer... -
Page 13: Replacing Pistons/O- Rings
4. The top of the piston should now be visible inside the cylinder, which is housed in the head of the nailer. H6143 16 Ga. Finish Nailer 5. Open the nose cover as if to clear a jammed nail. 6. Watch the discharge area and push the top of the piston with your finger. -
Page 14: Cleaning And Lubrication
Lubricating Special pneumatic tool oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 8) every 2 hours of con- tinuous use. - Page 15 H6143 PARTS BREAKDOWN H6143 16 Ga. Finish Nailer...
- Page 16 PH6143084 SUPPORT SEAT PLN03M LOCK NUT M6-1 PH6143086 RUBBER HANDLE PH6143087 END CAP GASKET PH6143088 END CAP PH6143089 AIR PLUG PH6143090 AIR PLUG COVER PH6143091 CARRYING CASE PAW04M HEX WRENCH 4MM PAW05M HEX WRENCH 5MM H6143 16 Ga. Finish Nailer...
-
Page 17: Troubleshooting
2. Piston shaft is damaged. 3. Air pressure too low. Air blows out of 1. O-ring slipped out of groove or exhaust cap; nailer will not fire. H6143 16 Ga. Finish Nailer ing are damaged. from moving freely. of lubrication. valve. cated. -
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 19: Warranty Card
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times. - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...