For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below.
Page 3
UNINTENTIONAL STARTING. Do not carry tool with hand on trig- ger and always disconnect from air when not in use. H7945/H7946/H7995 26° Angle Nailer 17. DISCONNECT TOOLS before ser- vicing, changing accessories, or moving to another location. 18. DO NOT OVERREACH. Keep proper footing and balance at all times.
Seek formal training or research sources that specialize in pneumatic tools. MAINTENANCE: Always disconnect air from the nailer when servicing or installing nails. During adjustments or maintenance, a nailer connected to air may fire accidentally, causing serious personal injury. H7945/H7946/H7995 26° Angle Nailer...
Page 5
Serious personal injury may result if safety or operational information is not understood or followed. H7945/H7946/H7995 26° Angle Nailer Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed.
INTRODUCTION Foreword We are proud to offer the Grizzly Model H7945/H7946/H7995 26° Angle Nailer. This nailer is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s...
Page 7
When you are completely satisfied with the condition of the shipment, you should inventory the equipment. Figure 1. Model H7945 /H7946/H7995 inventory. H7945/H7946/H7995 26° Angle Nailer SETUP After you open the nailer box, you should find the following.
Tool Quick Coupler Figure 2. Typical filter/lubricator/regulator installation order. Check the current Grizzly catalog for avail- ability of this unit. If you plan on install- ing a filter/lubricator/regulator unit in your compressed air system, always follow the connection instructions that come with the unit.
Page 9
— If the nailer does fire when the trigger is pulled, without the safety nose mechanism being depressed, immediately disconnect the nailer from the air supply and call Grizzly Technical Support at (570) 546- 9663 for help.
Page 10
Figure 5. Nail Strip magazine. guide it forward to push the nail strip to the nose of the nailer. (Do not let it snap.) H7945/H7946/H7995 26° Angle Nailer...
Page 11
3. Slide the pusher to the rear of the mag- azine and latch it into the lock notch. 4. Move the nails to the rear of the maga- zine and remove them by hand. H7945/H7946/H7995 26° Angle Nailer Rotating the Exhaust Cover The exhaust cover rotates as needed to direct the exhaust away from you.
— If the nail penetrates the wood to the depth you want, continue with your intended operations. — If the nail either went too far or not far enough, adjust the depth of fire by following the procedures listed on Page 11. H7945/H7946/H7995 26° Angle Nailer...
3. Connect the nailer to the air supply, test the nail depth, and repeat this entire procedure if necessary until the nail depth is satisfactory. H7945/H7946/H7995 26° Angle Nailer Clearing Jammed Nails A jammed nail must be cleared before the nailer is used again.
Grizzly: call 1-800-523-4777. The Piston Repair Kit part number for Model H7945 is PH7945090; the Piston Repair Kit part number for Model H7946 is PH7946090; the Piston Repair Kit part number for Model H7995 is H7995090.
H7945/H7946/H7995 26° Angle Nailer Lubricating Special pneumatic tool oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 10) every 2 hours of continuous use.
Page 19
PH7945041 NOSE PH7945042 SPRING PH7946043 CORE TRIP PSBS24M BUTTON HD CAP SCR M4-.7 X 10 PH7945045 RUBBER PAD PH7946046 MAGAZINE H7945/H7946/H7995 26° Angle Nailer REF PART # DESCRIPTION PH7945047 MAGAZINE COVER PH7945048 NAILER GUIDE PSB33M CAP SCREW M5-.8 X 12...
Page 21
PH7945041 NOSE PH7945042 SPRING PH7995043 CORE TRIP PSBS24M BUTTON HD CAP SCR M4-.7 X 10 PH7945045 RUBBER PAD PH7995046 MAGAZINE H7945/H7946/H7995 26° Angle Nailer REF PART # DESCRIPTION PH7945047 MAGAZINE COVER PH7945048 NAILER GUIDE PSB33M CAP SCREW M5-.8 X 12...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
Page 26
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...