Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H6332
Summary of Contents for Grizzly H6332
- Page 1 ⁄ " BRAD NAILER OWNER'S MANUAL COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
-
Page 2: Safety Instructions For Pneumatic Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. - Page 3 16. REDUCE UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always disconnect from air when not in use. H6332 1 ⁄ " Brad Nailer 17. DISCONNECT TOOLS before ser- vicing, changing accessories, or moving to another location.
-
Page 4: Additional Safety Instructions For Nailers
COMPRESSED AIR RATING: Do not connect the nailer to compressed air that exceeds 120 PSI. CHECK VALVE: Do not use a check valve or any other fitting that allows air to remain in the tool. H6332 1 ⁄ " Brad Nailer... - Page 5 85-90 deci- bels. To protect your hearing, always wear ANSI approved ear protection when operating this nailer. H6332 1 ⁄ " Brad Nailer Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed.
-
Page 6: Contact Info
INTRODUCTION Foreword We are proud to offer the Grizzly Model H6332 1 ⁄ " Brad Nailer. This model is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-... - Page 7 Unpacking Your Model H6332 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing mate- rials for possible inspection by the car- rier or its agent.
-
Page 8: Compressed Air System
Compressed Air System The Model H6332 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres- sure for your model. Before using your new nailer, regulate the air pressure on your air compressor to the minimum PSI for your model. - Page 9 If this occurs, call Grizzly Technical Support at (570) 546-9663 for help. — If you find that the safety nose mechanism is not working properly, check the lubrication of its sliding components.
- Page 10 Loading When replacing nails in your Model H6332, follow these guidelines: Gauge: Length: " – 1 ⁄ " Capacity: 100 To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Grip the nailer firmly, release the catch lever and slide the magazine pusher open, as shown in Figure 3.
-
Page 11: Adjusting Depth
— If the nail either went too far or not far enough, then go to the Adjusting Depth section on this page. H6332 1 ⁄ " Brad Nailer Adjusting Depth A depth adjustment knob is attached to the nose for setting the nail depth. -
Page 12: Clearing Jammed Nails
Throw the damaged nail away and insert a new nail stick that only contains clean, undamaged nails. DO NOT use dirty or damaged nails! Slide the pusher back until it locks into position. H6332 1 Nose Tip ⁄ " Brad Nailer... -
Page 13: Replacing Pistons/O- Rings
A replacement piston and O-ring kit, part PH6332082, may be purchased for the Model H6332. Always disconnect air from nailer whenever servicing! During mainte- nance, a nailer connected to air may... -
Page 14: Cleaning And Lubrication
Lubricating Pneumatic tool oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 8) before every use, or after 2 hours of continuous use. -
Page 15: Troubleshooting
Air blows out 1. O-ring slipped out of groove of exhaust cap; or damaged inside nailer. nailer will not fire. H6332 1 ⁄ " Brad Nailer Solution 1. O-rings must be replaced & operation of safety nose must be checked. - Page 16 H6332 PARTS BREAKDOWN � � �� � �� � �� � �� � �� � �� � �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��...
- Page 17 H6332 PARTS LIST REF PART # DESCRIPTION PH6332001 STEEL BALL PH6332002 ORIENTATION SPRING PH6332003 SHOULDER BOLT M4-.7 X 16 PH6332004 DIRECTION SPRING PH6332005 AIR DEFLECTOR PSB15M CAP SCREW M5-.8 X 20 PLW01M LOCK WASHER 5MM PH6332008 CYLINDER CAP PH6332009 SEALING WASHER 18MM PH6332010 O-RING 17 X 2.65...
-
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 19: Warranty Card
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times. - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...