Page 1
MC Series 8 X 2 Mic/Line Mixers 8002MCB-XLR User Manual 8002MCB-FP 8002 MCB-PHNX www.intelix.com...
Page 2
If a unit which is out of warranty needs repair, the dealer must pay for shipping, replacement parts, and a fixed $100/hr labor fee. Normal Intelix credit terms apply to billable repairs. If a unit is returned and found to work according to factory specifications, a standard $100 service fee is billed regardless of warranty status.
User Manual 1.0 Introduction This manual describes the components and operation of the Intelix MC Series line of mic/line mixers. As with all Intelix products, the MC Series ensures the highest quality audio signal production and control through easy-to-use features.
2. If condenser mics are not otherwise powered, set the phantom power switch to on. 3. In the event of occasional excessive output level, set the limiter switch to on. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
10 11 12 8002MCB-XLR D E F 8002MCB-XLR and 8002MCB-PHNX Front Panel Main/Auxiliary Bus Selector (one per channel) - 4-position switch which selects the destination of the input channel. Route channels as follows: A) Main Bus - M switch up, A switch down...
Page 7
4 5 6 7 8 9 11 12 8002MCB-PHNX 8002MCB-XLR and 8002MCB-PHNX Rear Panel Ground Lift Jumper - access to ground lift jumper J19. AC Power Connector - mixer power supply input; accepts a 4-pin DIN connection from an 18VCT 1.5 amp transformer.
Page 8
Auxiliary Ouput Volume Knob - controls the output signal volume of the auxiliary bus. Headphone Jack - 1/4 inch-diameter TRS mono jack Power Switch Button - “in” position powers unit; “out” position powers down unit. LED displays status. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562...
Page 9
(ninth) input connection directly to the summing buses as selected by the internal jumpers. Main Input Connector - XLR or Phoenix balanced/unbalanced connector. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562...
3.1 Unpacking and Connecting the Mixer 1. Take the mixer out of box and inspect for shipping damage. If there is obvious physical damage to the outside of the mixer, contact your Intelix representative before you begin installation. 2. Turn all mixer and amplifier Volume Control Knobs to zero.
2. Toggle the amplifiers to the audio levels desired and use the mixer’s front panel volume knobs to make final adjustment to levels. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
Reduce the input gain/trim control by turning it counterclockwise. 3.6 Recommended Input Wiring Methods Intelix recommends the following input wiring methods depending on your application. Balanced Source to Balanced Input Shown is the typical wiring method for a balanced source device.
The compressor smooths transients. The limiter is used to prevent a signal from exceeding a certain level. This function guards against amplifier or recording level overloads. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
Page 14
The factory setting for the threshold is +4 dBu. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562 Fax: 608-831-1833...
User Manual 3.8 Special Features Activation Intelix 8002MCB mixers have several built-in features which are easily activated through internal adjustments inside the mixer chassis. Changing the selection of all built-in features requires only the correct placement of internal jumpers or varying the settings of an internal potentiometer.
Headphone amp also controlled by the Aux volume knob, but not independently of the Aux output. Note: Never install jumpers in both positions J1 and J2. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562...
User Manual User Manual 3.9 Linking Intelix 8002MCB mixers may be linked in several ways. The two principal methods of linking are “simple” and “complex.” Simple linking is the expansion to more than 8 inputs by connecting two 8002MCB mixers via the auxiliary bus.
Page 18
2) For both mixers, remove jumper from J2 position and place it in position J1. This gives internal control of both auxiliary buses. 3) Using external cables, connect the two mixers as shown below. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
If another AC supply is used instead, it should be of equal voltage and have at least a 21 Volt-Amp rating. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562...
It should be removed, unless the mixer is in a nonmetal cabinet. Check for unbalanced connections; use balanced connections, if possible. For all unbalanced connections, try to disconnect the signal line ground to “lift” the ground. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
-10 dB. Summing Junction - The point in the MC circuitry where the audio signals are mixed. XLR - Rugged, locking, multi-pin balanced connectors frequently used to terminate cables. www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX...
Page 23
MC Series User Manual User Manual User Manual User Manual User Manual www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562 Fax: 608-831-1833...
Page 24
MC Series User Manual User Manual User Manual User Manual User Manual www.intelix.com Intelix LLC Phone: 608-831-0880 2222 Pleasant View Road Toll-Free: 1-866-4-MATMIX Middleton, WI 53562 Fax: 608-831-1833...
Need help?
Do you have a question about the 8002MCB-XLR and is the answer not in the manual?
Questions and answers