Atdec Telehook Installation Instructions

C

Attaching the Display to the Wall Plate

C.1. Attaching the Display to the Wall Plate
Note: This procedure will require two persons
Back Plate
Mounting
Slots
Note: For demonstration purposes, the wall
has been omitted from the above image.
With the mount attached to the display, lift the
display and slide the Back Plate into the Mounting
slots to ensure a secure connection.

Security Option

D
Note: For demonstration purposes, the display
has been omitted from the image below.
Back plate
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.04.07 ©
C.2. Pivot Head Load Capacity Adjustment
M12 Hex Nut
Tighten
Adjusting the Pivot Head to suit the weight of the
Display
The Pivot head is factory set to hold
approximately 35kgs (77lbs). If the display is not
holding its position when placed on the wall it
may be necessary to remove the display from
the wall and tighten the M12 Hex Nut on the
back of the Pivot Head using a 17mm (
socket wrench or shifter. To achieve a one-touch
effortless adjustment setting it is advised that the
nut be tightened at half turns and re-tested, until
the desired friction is achieved. Alternatively the
M12 Hex Nut can be over tightened in order to
lock the display in position.
For additional security,
it is suggested that a
Padlock be attached to
the Back plate as shown.
The Padlock (not supplied)
should have a shackle
diameter no larger than
3
4mm ( /
16
Mounting Slot
3
Shackle 4mm ( / ")
16
diameter or less
Padlock
Important Notes
The Telehook 30-50 Universal Rotating Wall Mount supports flat panel displays from 30" (76cm) to 50" (127cm)
and supports a maximum load of 85kgs (187lbs).
This product is factory set to support 35kgs (77lbs), and will need to be adjusted if the display is heavier or lighter.
The manufacturer does not accept responsibility for incorrect installation.
Component Checklist
11 / ")
16
Extension Plate
Bracket Plate (x2)
TOOLS REQUIRED:
Power Drill
12mm or 8mm Drill Bit
Phillips Head Screw Driver
Spirit Level
17mm ( 11 / ") Socket Wrench
16
or Shifter
A

Mounting the Wall Plate

Masonry Wall
").
Masonry
Wall Plug
Note: Ensure the Wall Plate
is mounted with the narrow
end of the Mounting Slot
at the bottom.

Installation Instructions

TELEHOOK
30"-50" UNIVERSAL ROTATING WALL MOUNT
Pivot Head
Bracket (x2)
Wall Plate
Timber Stud Wall
Note: It is recommended to
TIP: Use a spirit
mount the Wall Plate by firmly
level to ensure the
1
12mm ( / ")
fixing the four Coach Screws
2
wall plate is
Hole
into two studs. However, if the
horizontal
weight of the display is less than
50kgs (110lbs), it is possible to
mount the Wall Plate to one stud
Wall Plate
by fixing the two Coach Screws
through the two Centre holes.
Large Washer
Note: Ensure the Wall Plate is
mounted with the narrow end of the
Coach Screw Mounting Slot at the bottom.
Bits Box
Mounting
Screws
Masonry Wall
Coach
M8x20mm
Plug (x4)
Screw (x4)
Phillips Head
Screw (x4)
Spacer Large
M6x16mm
Bush (x4) Washer (x4)
Phillips Head
Screw (x6)
M6x16mm Socket
M5x16mm
Allen Key
Drive Screw (x12)
Phillips Head
Screw (x6)
M4x16mm
Small
Multi
Phillips Head
Washer (x4)
Washer (x4)
Screw (x6)
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
Timber
Stud
5
8mm ( / ")
16
Hole
Centre Holes
Large
Washer
Coach Screw